If you’re experiencing issues with your Frigidaire Affinity washer, understanding the error codes can help you diagnose and fix the problem. This guide will provide you with a comprehensive list of Frigidaire Affinity washer error codes and troubleshooting tips to resolve them.
Key Takeaways:
- Understanding Frigidaire Affinity washer error codes can help you identify and fix issues
- Use the error codes to troubleshoot and resolve problems with your washer
- Follow the provided troubleshooting tips to address specific error codes
- If you’re unsure or need further assistance, consider contacting Frigidaire customer support or a professional technician
How to Read Error Codes on Frigidaire Affinity Washer
If you’re facing issues with your Frigidaire Affinity washer, reading the error codes can provide valuable insights for troubleshooting. By entering the diagnostic mode, you can easily retrieve error codes that indicate specific problems. Here’s how you can do it:
- Press any button on the control panel to wake the washer.
- Simultaneously press and hold the Start/Pause and Cancel buttons.
- The display will show the failure code, which typically starts with an ‘E’ followed by numbers, a number and a letter, or two letters.
- The control will emit a beep sound, and certain indicator lights may flash.
Reading the error codes will help you understand the underlying issues with your Frigidaire Affinity washer, enabling you to take appropriate actions for troubleshooting and resolving the problems.
How to Clear Error Codes on Frigidaire Affinity Washer
If you’re encountering error codes on your Frigidaire Affinity washer, it’s important to clear them in order to restore normal operation. Follow the steps below to clear the latest stored error code:
- Turn the Program Knob to the start position of the leftmost cycle.
- Press the Start/Pause button to initiate the cycle.
- Press the Cancel button to stop the cycle and turn off the LEDs.
- Press the Cancel button again to turn on the LEDs.
- Within 5 seconds, press and hold the Option and Start/Pause buttons simultaneously until the LEDs start sequentially chasing.
- Release the buttons and turn the program knob clockwise seven clicks.
- The control will signal the last error code.
- To clear the error code, press and hold the Options and Start/Pause buttons for 3 seconds.
You can exit Diagnostic Mode by either unplugging the power cord or turning the program knob clockwise.
Note: Clearing the error codes is an essential step in troubleshooting your Frigidaire Affinity washer. By following these instructions, you can reset the error codes and proceed with identifying and resolving any underlying issues.
Frigidaire Affinity Washer Error Code E11
If you’re experiencing error code E11 on your Frigidaire Affinity washer, it means that the fill time is too long. This issue can be caused by problems with the water supply or the water inlet valve.
To resolve this error code, follow these troubleshooting steps:
- Check the water supply: Ensure that the water supply to the washer is turned on and that there are no issues with the water pressure or flow.
- Inspect the water inlet valve: The water inlet valve may be clogged or faulty, preventing proper water intake. Clean the valve and remove any obstructions. If cleaning doesn’t resolve the issue, you may need to replace the water inlet valve.
If the error code E11 persists after troubleshooting these issues, it is recommended to seek professional assistance or contact Frigidaire customer support for further help.
| Error Code | Description | Troubleshooting Steps |
|---|---|---|
| E11 | Fill time too long |
|
Frigidaire Affinity Washer Error Code E13
Error code E13 on a Frigidaire Affinity washer indicates a water leak in the tub or an air leak in the air bell. It’s essential to inspect both the tub and the air bell for any signs of leakage or damage to determine the cause of the error. Identifying the source of the leak is crucial to prevent further damage and resolve the error code effectively.
To inspect the tub, visually examine it for any visible signs of water leakage. Look for wet spots, puddles, or dripping water around the tub or at the base of the washer. Additionally, check the air bell, which is located at the bottom of the tub. Inspect the air bell for cracks, holes, or any visible signs of damage.
If you detect a water leak in the tub, ensure that all hoses and connections are tightly secured. Check the water inlet valve and the drain hose for any obstructions or damages that could contribute to the leakage. If necessary, replace any faulty components or repair any damaged areas to address the leak and resolve the error code.
For an air leak in the air bell, check the air bell assembly for loose or disconnected hoses. Ensure that all connections are securely fitted and that there are no blockages in the air bell system. If you find any issues, reattach or replace the affected hoses to rectify the air leak and resolve the error code.
Resolving error code E13 on your Frigidaire Affinity washer requires addressing the underlying water or air leak issue. By carefully inspecting the tub and air bell, you can identify the source of the leak and take appropriate measures to fix the problem, ensuring proper functioning of your washing machine.
Frigidaire Affinity Washer Error Code E21
Error code E21 on a Frigidaire Affinity washer indicates that water is not pumping out fast enough. This can lead to issues with the washing cycle and may result in incomplete drainage. To resolve this error code, you can try the following troubleshooting steps:
Step 1: Check the Drain Hose
Inspect the drain hose for any obstructions or kinks that may be restricting the flow of water. Clear any debris or blockages if necessary. Ensure that the drain hose is properly connected and positioned to allow for smooth water drainage.
Step 2: Examine the Drain Pump
The error code E21 may also be triggered by a faulty drain pump. Inspect the drain pump for any signs of damage or irregularities. If you notice any issues, such as a broken impeller or worn-out motor, it may be necessary to replace the drain pump.
Note: It is recommended to refer to the user manual or contact a certified technician for assistance with drain pump replacement.
By addressing possible obstructions in the drain hose and ensuring the functionality of the drain pump, you can effectively troubleshoot and resolve error code E21 on your Frigidaire Affinity washer.
Frigidaire Affinity Washer Error Code E23 and E24
If you encounter error codes E23 and E24 on your Frigidaire Affinity washer, it indicates a problem with the drain pump relay on the control board. This issue can occur if a wire is disconnected from the pump or if the pump itself is defective. To troubleshoot and resolve the error, follow these steps:
- Inspect the pump and wiring for any visible issues or damage.
- If you find a disconnected wire, reconnect it securely.
- If the pump appears faulty, it will need to be replaced with a new one.
- Additionally, if the problem persists, you may need to consider replacing the console control board.
By carefully examining the pump and wiring, reconnecting any disconnected wires, and replacing faulty components as necessary, you can address error codes E23 and E24 on your Frigidaire Affinity washer.
Note: If you are unsure about performing these troubleshooting steps yourself, it’s always recommended to seek professional assistance or contact Frigidaire customer support for further guidance.
Possible Causes of Error Codes E23 and E24:
| Cause | Solution |
|---|---|
| A wire is disconnected from the pump. | Reconnect the wire securely to the pump. |
| The drain pump is defective. | Replace the drain pump with a new one. |
| The console control board is malfunctioning. | Consider replacing the console control board if the issue persists. |
By addressing these possible causes and following the recommended solutions, you can effectively troubleshoot and resolve error codes E23 and E24 on your Frigidaire Affinity washer.
Frigidaire Affinity Washer Error Code E31 and E35
Error codes E31 and E35 on a Frigidaire Affinity washer indicate communication issues between the pressure sensor and the control board. These errors can prevent proper communication and affect the washer’s performance. To troubleshoot and fix these issues, follow the steps below:
- Inspect the wiring between the pressure sensor and the control board for any damage or loose connections.
- If you find any damaged wires or loose connections, carefully reconnect or repair them. Ensure all connections are secure.
- If the wiring appears to be in good condition, the problem may lie with either the pressure sensor or the control board.
- To determine the faulty component, refer to the Frigidaire Affinity washer’s user manual or contact Frigidaire customer support for guidance.
- If the pressure sensor is faulty, consider replacing it with a compatible replacement part.
- If the control board is determined to be the issue, you may need to replace it to resolve the error codes.
By following these troubleshooting steps, you can diagnose and address the communication issues between the pressure sensor and control board on your Frigidaire Affinity washer, effectively resolving the E31 and E35 error codes.
| Error Codes | Possible Causes | Solution |
|---|---|---|
| E31 | Communication issue between the pressure sensor and the control board. | Inspect wiring for damage or loose connections. Replace faulty pressure sensor or control board. |
| E35 | Communication issue between the pressure sensor and the control board. | Inspect wiring for damage or loose connections. Replace faulty pressure sensor or control board. |
Frigidaire Affinity Washer Error Code E41, E43, and E44
If you encounter error codes E41, E43, or E44 on your Frigidaire Affinity washer, the issue is likely related to the door switch or the console control board. It’s important to first ensure that the washer door is fully closed and securely latched. Check the door strike to make sure it is properly aligned and not damaged. If the door is closed correctly and the problem persists, you may need to replace either the door switch assembly or the console control board to resolve the error code.
If you’re unsure about the exact cause or how to perform the replacement, it’s recommended to seek professional assistance or contact Frigidaire customer support for further guidance.
Error Code Solutions
| Error Code | Possible Cause | Solution |
|---|---|---|
| E41 | Door switch issue | Ensure the door is fully closed and check the door strike. Replace the door switch assembly if necessary. |
| E43 | Console control board problem | Inspect the console control board for any visible damage. If necessary, replace the control board. |
| E44 | Door switch or control board malfunction | Check the door switch and control board for any issues. Replace the faulty component accordingly. |
By following these troubleshooting steps and taking the necessary actions, you can resolve the Frigidaire Affinity washer error codes and get your washing machine back to optimal functionality.
Conclusion
Understanding Frigidaire Affinity washer error codes is crucial for troubleshooting and resolving issues with your washing machine. By following the provided error code guide and implementing the troubleshooting tips, you can effectively identify the problem and take the necessary steps to fix it.
By familiarizing yourself with the error codes and their meanings, you can quickly diagnose any issues that may arise with your Frigidaire Affinity washer. This knowledge empowers you to address the problem promptly, saving time and money on potential repairs or replacements.
If you encounter difficulties in resolving the error codes or have further questions, it’s recommended to seek professional assistance or contact Frigidaire customer support. Their expertise and guidance can provide tailored solutions and ensure your Frigidaire Affinity washer is back to its optimal performance.
FAQ
How do I read the error codes on my Frigidaire Affinity washer?
To read the error codes on a Frigidaire Affinity washer, enter diagnostic mode by pressing any button on the control panel to wake the washer, then press and hold the Start/Pause and Cancel buttons simultaneously. The failure code will appear on the display as an E followed by two numbers, a number and a letter, or two letters. The control will beep, and certain indicator lights will flash.
How do I clear the error codes on my Frigidaire Affinity washer?
To clear the latest stored error code on your Frigidaire Affinity washer, turn the Program Knob to the start position of the leftmost cycle and press Start/Pause to start the cycle. Press Cancel to stop the cycle and turn off the LEDs. Press Cancel again to turn on the LEDs. Within 5 seconds, press and hold the Options and Start/Pause buttons until the LEDs start sequentially chasing. Release the buttons and turn the program knob clockwise seven clicks. The control will signal the last error code. To clear the error, press and hold the Options and Start/Pause buttons for 3 seconds. You can exit Diagnostic Mode by unplugging the power cord or turning the program knob clockwise.
What does error code E11 on a Frigidaire Affinity washer mean? How can I fix it?
Error code E11 indicates that the fill time is too long. This could be due to a problem with the water supply or the water inlet valve. Check the water supply and ensure there are no obstructions in the water inlet valve. If the issue persists, you may need to replace the water inlet valve.
What does error code E13 on a Frigidaire Affinity washer indicate? How can I resolve it?
Error code E13 signifies a water leak in the tub or an air leak in the air bell. Inspect the tub and air bell for any signs of leakage or damage. If a leak is detected, you’ll need to address the issue to prevent further damage and resolve the error code.
My Frigidaire Affinity washer is displaying error code E21. What does it mean, and how do I troubleshoot it?
Error code E21 indicates that water is not pumping out fast enough. This could be due to a clogged drain hose or a faulty drain pump. Check the drain hose for any obstructions and clear them if necessary. If the drain hose is clear, you may need to replace the drain pump to resolve the error code.
My Frigidaire Affinity washer is showing error codes E23 and E24. What should I do to fix this issue?
Error codes E23 and E24 point to a problem with the drain pump relay on the control board. This can be caused by a wire being disconnected from the pump or a defective pump. Inspect the pump and wiring for any issues. If a wire is disconnected, reconnect it. If the pump is faulty, you’ll need to replace it. Additionally, you may need to replace the console control board if the issue persists.
What do error codes E31 and E35 on a Frigidaire Affinity washer mean? How can I resolve them?
Error codes E31 and E35 indicate communication issues between the pressure sensor and the control board. Check the wiring between the pressure sensor and the control board for any damage or loose connections. If the wiring is in good condition, you may need to replace the pressure sensor or the control board to resolve the error codes.
My Frigidaire Affinity washer is displaying error codes E41, E43, and E44. What could be causing these errors, and how can I fix them?
Error codes E41, E43, and E44 involve issues with the door switch and the console control board. Ensure that the door is fully closed and check the door strike. If the door is closed and the issue persists, you may need to replace the door switch assembly or the console control board to fix the error codes.
Can understanding Frigidaire Affinity washer error codes help me troubleshoot and fix issues with my washer?
Yes, understanding Frigidaire Affinity washer error codes can help you identify and resolve issues with your washing machine. By following the troubleshooting tips provided in this guide, you can effectively address error codes and restore your Frigidaire Affinity washer to normal operation. If you encounter any difficulties or have further questions, seek professional assistance or contact Frigidaire customer support.