The Maytag Bravos XL doesn’t break down cheaply, but it’s not immune to breaking down. You may even need to run diagnostics and interpret the error codes that it shows. So, it’s best to have the essential Maytag Bravos Xl washer troubleshooting tips, and that’s where this guide comes in.
Common troubleshooting problems include a Maytag Bravos washer stuck on sensor mode, a control panel not working, and a washer that won’t start, spin, agitate, fill up, drain, or move to the next cycle or one that overflows.
On that note, I’ll discuss all these nine issues in detail to help you fix them accordingly. And to crown things. I’ll discuss the most typical error codes you can interpret on a Maytag Bravos XL and resolve them.
9 Maytag Bravos XL Washer Troubleshooting Problems
Check out nine of the most familiar Maytag Bravos XL problems, their potential causes, and respective DIY fixes:
| Washer Problem | Probable Cause | DIY Solution | |
| 1. | Stuck On Sensor | Stuck keypad, incorrect setting, faulty control board, water inlet valve, timer, lid lock, or sensor fault | Unstuck any stuck keypad and replace any defective component, and once through, reset your washer to fix any issue |
| 2. | Control Panel Not Working | Unlocked lid or activated control lock | Lock the lid and deactivate the control lock before running the washer |
| 3. | Won’t Start (Turn On) | Power failure, faulty main control, or power cord failure | Ensure there’s power and that the power cord is working and well plugged. Replace the main control if faulty |
| 4. | Won’t Spin | The wrong setting, load imbalance, power failure or faulty drive belt, lid switch, actuator switch, or motor coupling | Choose the right wash setting and balance the load. Also, check for power failure and replace the faulty component |
| 5. | Won’t Agitate | Faulty drive belt, lid lock, motor, or main control | Replace the defective washer components |
| 6. | Won’t Fill Up | No water supply or due to drainage issues | Connect the water supply properly and fix any drainage issues present |
| 7. | Won’t Drain | Drain hose, drain pump, or filter valve | Unclog the drain and replace the drain pump if it’s faulty |
| 8. | Won’t Move To The Next Cycle | Clogged lid lock, or malfunctioning main control | Remove the obstruction on the lid and test the main control for malfunctioning (replace if faulty) |
| 9. | Overfilling | A problem with the pressure hose, valve, pressure switch, or control | Replace the pressure hose valve or pressure switch if its defective or worn out |
Maytag Bravos XL Washer Troubleshooting Guide
Now, let’s dissect the nine issues shared in the above table:
1. Maytag Bravos XL Sensor Stuck on Sensor
So, your Maytag Bravos XL is stuck on sensing? The chances are that its due to any of these Maytag Bravos Xl washer sensor problems:
- Stuck keypad – A stuck keypad could be preventing your washer from going beyond sensing mode. So, see if there’s one jammed and try to unclog it.
- Incorrect setting – Your washer may need a reset to fix a wrong setting. So, do it.
- Faulty control board – The control board could be malfunctioning, therefore failing to relay the correct information. In that case, you may have to replace it.
- Faulty water inlet valve – if the water inlet valve does not regulate water flow, the washer may stay in sense mode. So, test it with a multimeter, and if you find it faulty, replace it.
- Faulty timer, lid lock, or sensor – Test the three with a multimeter and replace them if defective.
2. Maytag Bravos Xl Washer Control Panel Not Working
If the control panel is not working, the chances are the lid is locked. An unlocked lid deactivates the control panel’s function, which means the touchpad may not respond when you try to operate it.
Note, however, that it doesn’t apply to all control panels. The other thing to check is the control lock. If it’s on (activated), the control panel won’t work.
Fix
Check the lid to ensure it’s locked before powering the washer. And while at it, deactivate the control lock. Ensure the control lock light is off before starting the washer.
If it doesn’t work, it may be time to replace your control panel as it could be faulty.
3. Maytag Bravos Xl Washer Won’t Start
If your washer won’t turn on, you should consider these possibilities:
- Power failure – It could be that there’s nothing wrong with your washer, only that there’s no electricity or that you haven’t switched the washer on. It could also be that you haven’t plugged in the power cord correctly. So, check all that.
- Power cord failure – Test the power cord with a multimeter to ensure it’s working. If there’s no continuity, the power cord needs replacing.
- Faulty main control – There could also be an issue with your main control, stopping the washer from powering on. In that case, the main control could have been installed properly or is faulty. So, test it, and if it’s defective, replace it.
4. Maytag Bravos Xl Washer Won’t Spin
There are several explanations for your Maytag Bravos washer which won’t spin. Here are the commonest:
- Wrong setting – You must choose the right spin setting for your Maytag washer to spin depending on the clothes you are washing.
- Load unbalanced/overload – Check your laundry to ensure it’s even and that you don’t overfill. That’ll bring balance and enable your washer to spin usually.
- Power failure – Check the power cord to ensure it’s well plugged in and ensure there’s power. You can also test the power cord for continuity using a multimeter.
- Faulty drive belt, lid switch, actuator switch, or motor coupling – Use a multimeter to test the condition of all these four components. If one shows no continuity, it’s defective, and it’s a good idea to replace it.
5. Maytag Bravos Xl Washer Won’t Agitate
If your Maytag Bravos XL won’t agitate, it’s hard to overlook the drive belt, lid lock, motor, and main control. One of the four components could be faulty.
Start with the lid lock. If you cannot close the washer’s lid, then the problem is the lid lock, which is faulty.
In that case, replace it. But if the lid lock is okay, physically examine the drive belt. If it looks worn out, replace it.
But if the drive belt is fine, inspect the motor and the main control. One of them could be why your washer won’t agitate. So, replace the faulty component.
6. Maytag Bravos Xl Washer Won’t Fill Up with Water
You cannot expect your Maytag washer to fill up with water if there’s no water supply in the first place. So, start by checking the water supply.
If the water supply is okay, the problem could be poor drainage, and it could relate to a loose connection, faulty drain valve, or clogged filter.
For that reason, check all elements of your washer’s drain to ensure there’s no obstruction. If there’s no proper drainage or good water supply, the washer may never fill up.
7. Maytag Bravos Xl Washer Won’t Drain
If your Maytag Bravos XL won’t drain, there’s a major issue with the drain. It could be a jammed drain hose, drain pump, or valve. So, you’ve to check out the three for possible clogging.
If the issue is not drain-related, you’ve to look at the pump’s condition. It could be that the drain pump is faulty and thus requires a replacement.
But if that’s not it, inspect the main control. There could be a problem with the main control. If you cannot fix it, talk to a Maytag washer technician.
8. Maytag Bravos XL Washer Won’t Start Cycle
If your washer cannot start a cycle, the chances are that the main control or the lid lock has an issue. The main control might be faulty, so you’ll need to test it using a multimeter to see if it’s working.
If not, you’ll need to replace it. As for the lid lock, it could be that it’s faulty. In that case, look for possible obstruction on the lid lock that prevents you from locking the lid.
Moving to the next cycle may be challenging if you cannot lock the lid as the washer becomes unresponsive. If the lid lock is faulty, you may have to replace it.
9. Maytag Bravos Xl Washer is Overfilling
Sometimes, the Maytag Bravos XL won’t just stop filling up with water. You’ll be dealing with flooding in such a case, which you can fix if you diagnose the problem first.
The reason why your washer overflows is that there’s a problem first. Your washer overflows because there’s a problem with the pressure hose, pressure switch, or valve.
So, you’ve to check all the three to ensure they are working correctly. You can test the pressure switch with a multimeter. But as for the valve, you need to check for clogging.
And when it comes to the pressure hose, ensure it’s not leaking. If it is, replace it.
5 Common Maytag Bravos XL Washer Error Codes
Here are five common Maytag Bravos XL error codes to troubleshoot:
1. Maytag Bravos XL Washer Problems UL Error
Error UL signifies an unbalanced load. The chances are that your laundry is not evenly spread on the washer. You could also have loaded the wrong load, such as heavy blankets and rugs. So, stop the machine and rearrange the load evenly in the washer.
2. Maytag Bravos Washer XL OL Error (Code F70)
The OL Error shows an overload. It could be that you’ve put too much load into the washer. So, stop your Maytag Bravos XL and reduce the load before running the machine.
3. Maytag Bravos Washer XL SD Error (Code F71)
SD Error signifies Suds detected. The error is likely to pop up if you use excess detergent. In that case, you should avoid using excess detergent.
Also, ensure you use the correct detergent. Avoid non-high-efficiency detergents.
4. Maytag Bravos XL Washer Troubleshooting F5 Error Code
Error code F5 on a Maytag Bravos XL shows that the lid is locked. An obstruction, even clothing, could stop the lid from closing. So, you’ve to check what’s obstructing the top and remove it.
5. Maytag Bravos Washer XL Error LD (Code F32)
Code LD signifies that the washer is taking longer to drain. Often, that’s because of a drain clog or kink or weak pump.
So, you’ve to check the drain and get rid of clogs and kinks. Ensure the drain hose doesn’t drain at the height of more than 96 inches and that the pump runs smoothly.
How to Reset Your Maytag Bravos XL Washer?
Remember, you won’t find the Maytag Bravos Xl washer reset button to press when you want to reset your washer. So, you’ve to be creative about it, and here are two ways to do it:
- Basic Reset – This approach requires you to power off the washer and unplug it from the power socket. Then, wait for roughly 5 minutes before plugging it back in and restarting the machine.
- Hard Reset – This approach is just the same as the basic reset, only that you’ve to wait for 30 minutes and not 5 minutes before plugging the cord back and powering the washer.
What were the results of the motor test and lid lock test in diagnostic mode?
During the manual diagnostic mode, the motor test was conducted and it was found to be functioning properly. Additionally, the lid lock test was performed and confirmed that the lid lock is in working order. Furthermore, the spin test was successfully carried out, with the machine being able to spin at all speeds as intended.
However, upon returning to the diagnostic mode, it was observed that the machine was getting stuck at C8 and continuing to agitate, even though there was no water present. Furthermore, the drain seemed to persistently run. This situation raises confusion and calls for further investigation into the possible causes of these unexpected actions.
Is there any friction in the basket engagement causing the issue?
According to the information provided, it is unclear whether there is any friction in the basket engagement causing the issue. The individual states that they do not know what it means by friction in the basket engagement and that there are no slow draining issues or suds. They believe that the problem lies in the confusion of the washing machine regarding whether it should be in spin or wash mode during the rinse and spin cycle. However, they cannot provide any additional details to further describe the issue.
Is there a link to the tech sheet for the model MVWB725BW0?
Here is the link https://www.searspartsdirect.com/manual/5zr525evya-003048/maytag-mvwb725bw0-washer-parts
What is the model number of the Maytag Bravos XL washer experiencing an error?
The model number of the Maytag Bravos XL washer experiencing an error is MVWB725BW0.
What steps have been taken to troubleshoot and fix the problem?
What concerns does the person have regarding the suggested solution?
The person is concerned about the cost of the control board and the possibility of other parts failing in the future.
What potential cause did the person consider based on the observed behavior?
If all four suspension rods are good, the control board may need to be replaced.
What specific behavior did the person observe during the diagnostic mode?
The machine hangs up in C8, continues to agitate, and the drain keeps running even though there is no water in it.
What were the results of the tests?
The motor test and lid lock test both checked out okay.
What tests have been performed to troubleshoot the issue?
The person performed a motor test and a lid lock test.
Common troubleshooting problems include a Maytag Bravos washer stuck on sensor mode, a control panel not working, and a washer that won’t start, spin, agitate, fill up, drain, or move to the next cycle, or one that overflows. It can be frustrating when your washer is not functioning as it should. But fear not, I’m here to guide you through the troubleshooting process.
Let’s dive into the nine most common Maytag Bravos XL problems, their potential causes, and the corresponding DIY fixes. By following these steps, you can get your washer back to its optimal performance.
1. Stuck On Sensor:
Probable Cause: This issue could be caused by a stuck keypad, incorrect setting, faulty control board, water inlet valve, timer, lid lock, or sensor fault.
DIY Solution: First, check if any keys on the control panel are stuck. If so, gently unstick them. If that doesn’t solve the problem, you may need to replace the defective component. Once you’ve addressed the issue, reset your washer to ensure proper functioning.
2. Control Panel Not Working:
Probable Cause: An unlocked lid or an activated control lock can prevent the control panel from working.
DIY Solution: Make sure the lid is locked and deactivate the control lock before running the washer. This simple step can often resolve the issue and get your control panel back up and running.
3. Won’t Start (Turn On):
Probable Cause: Power failure, faulty main control, or power cord failure can prevent the washer from starting.
DIY Solution: First, check if there is power by ensuring the power cord is securely plugged in and functional. If the power supply is not the issue, you might need to replace the main control if it is faulty.
4. Won’t Spin:
Probable Cause: The wrong setting, load imbalance, power failure, or faulty drive belt, lid switch, actuator switch, or motor coupling can cause the washer not to spin.
DIY Solution: Make sure you have selected the appropriate wash setting and check if the load is balanced. Additionally, verify if there is a power failure. If the issue persists, you may need to replace the faulty component to restore proper spinning functionality.
5. Won’t Agitate:
Probable Cause: A faulty drive belt, lid lock, motor, or main control can prevent the washer from agitating.
DIY Solution: To fix this problem, you will likely need to replace the defective component. This should restore the agitating function of your washer.
6. Won’t Fill Up:
Probable Cause: The absence of water supply or drainage issues can prevent the washer from filling up.
DIY Solution: Ensure that the water supply is properly connected and check for any drainage issues that may be impeding water flow. Addressing these problems should allow your washer to fill up as intended.
7. Won’t Drain:
Probable Cause: A clogged drain hose, faulty drain pump, or filter valve can hinder the draining process.
DIY Solution: To resolve this issue, you need to unclog the drain hose and, if necessary, replace the drain pump. This should allow proper drainage from your washer.
8. Won’t Move To The Next Cycle:
Probable Cause: A clogged lid lock or a malfunctioning main control can prevent the washer from progressing to the next cycle.
DIY Solution: Remove any obstructions on the lid and test the main control for malfunctions. If the main control is faulty, replacing it should resolve the issue and enable your washer to advance to the next cycle.
9. Overfilling:
Probable Cause: The pressure hose, valve, pressure switch, or control may be causing the washer to overfill.
DIY Solution: If you notice your washer is overfilling, you should consider replacing the pressure hose, valve, or pressure switch if they are defective or worn out. This should prevent excessive water from entering your washer.
By following these troubleshooting steps, you can identify the underlying causes of common Maytag Bravos XL problems and resolve them on your own. With a little patience and these DIY solutions, you can have your washer back in working order without the need for costly repairs or replacements.
What are the symptoms of the washer not spinning and agitating slowly?
If your Maytag Bravos XL washer is experiencing issues with spinning and agitating slowly, there are several potential causes to consider. Let’s explore the symptoms and possible solutions:
4. Maytag Bravos Xl Washer Won’t Spin
One common explanation for a washer that won’t spin is selecting the wrong spin setting. It is important to choose the appropriate spin setting based on the type of clothes being washed.
Another possible reason is an unbalanced or overloaded load. Ensure that the laundry is evenly distributed and not exceeding the recommended capacity. Maintaining balance will allow the washer to spin properly.
Additionally, check the power cord to ensure it is securely plugged in and that there is an adequate power supply. You can verify the continuity of the power cord using a multimeter.
Faulty components such as the drive belt, lid switch, actuator switch, or motor coupling can also cause the washer to not spin. To determine if any of these components are defective, use a multimeter to test for continuity. If one of the components shows no continuity, it is recommended to replace it accordingly.
5. Maytag Bravos Xl Washer Won’t Agitate
When your Maytag Bravos XL washer fails to agitate, it is crucial to examine the drive belt, lid lock, motor, and main control for potential issues.
Start by checking the lid lock. If the washer’s lid cannot be securely closed, then a faulty lid lock is likely the cause. In this case, replacing the lid lock is recommended.
If the lid lock appears to be functioning correctly, visually inspect the drive belt. If it shows signs of wear or damage, replacing the drive belt may resolve the agitation problem.
However, if the drive belt is in good condition, it is advisable to inspect the motor and main control for potential faults. Either of these components could be the underlying cause of the washer’s failure to agitate. If a faulty component is identified, it is recommended to replace it accordingly.
By considering these potential causes and following the suggested solutions, you can troubleshoot your Maytag Bravos XL washer to determine the exact reason behind the slow spinning and agitating issue.<
Closing Remarks On Maytag Bravos XL Washer Troubleshooting!
The Maytag Bravos XL washer is often easy to troubleshoot if you know how to identify typical faults and interpret specific error codes.
Hopefully, the above troubleshooting guide can help you fix your washer problem and avoid paying someone to do the job for you.
Also Read: