If you own a Maytag front load washer and are experiencing issues, understanding the fault codes can help you troubleshoot the problem quickly. These error codes provide valuable information about what may be causing the malfunction.
If you have tried the suggested solutions for the specific error code and are still unable to resolve the issue, it may be time to seek professional assistance. Contact Maytag directly or schedule a service online for expert help.
Key Takeaways:
- Maytag washer fault codes can help diagnose problems.
- If the error code persists, reach out to Maytag or schedule a service online.
- Understanding specific error codes can save time and frustration in troubleshooting.
- Refer to the owner’s manual for specific button locations on older models.
- For some error codes, pressing and holding the button or unplugging the washer may help.
LOC or LC Error Codes
If you’ve encountered the LOC or LC error code on your Maytag washer, don’t panic. This code simply indicates that the control lock has been activated. The control lock feature is designed to prevent accidental changes to the settings during a cycle.
To remove the LOC or LC error code, try the following steps:
- First, touch the Control Lock button on your washer’s control panel. This button is typically labeled with a padlock symbol.
- If that doesn’t work, consult your Owner’s Manual for the specific button on older models. The manual will provide you with detailed instructions on how to unlock the controls.
- If the error code persists, try pressing and holding the Control Lock button for a few seconds. This may override the lock and restore normal operation.
- Alternatively, you can try unplugging the washer from the power source for about a minute. This can help reset the control lock function.
If none of these steps resolve the issue and the LOC or LC error code continues to appear, it’s recommended to contact Maytag customer service for further assistance.
dET Error Code
If you own a Maytag washer and encounter the dET error code, don’t worry, we’ve got you covered. This code usually appears when the detergent cartridge is not detected in the dispenser. However, if you’re using single-load doses of detergent, you can ignore this message as it doesn’t affect the operation of the washer.
To resolve the issue, follow these steps:
- Make sure the dispenser cartridge is inserted correctly. Check if it is properly positioned and snapped into place.
- Ensure that the drawer is shut completely. Sometimes, it may not be fully closed, causing the error code to display.
If the dET error code persists after following these steps, you may need to contact a professional technician for further assistance. They can help diagnose and resolve any underlying issues with your Maytag washer.
Int Error Code
The Int error code may appear on your Maytag washer, indicating that the cycle has been paused or canceled. It is normal for the washer to take some time to stop spinning and drain before displaying this error code. If you encounter this error code, follow the steps below to clear it:
- Press the pause or cancel button twice.
- Press the power button once.
If the error code is still displayed after performing these steps, you can try unplugging the washer or disconnecting the power for one minute. This may help reset the system and remove the code.
For a visual reference, refer to the diagram below:
rL or F34 Error Codes
The rL or F34 error codes on your Maytag washer indicate that items have been detected in the washer during the Clean Washer cycle. To clear the code, you need to remove the items from the drum and restart the Clean Washer cycle. This error code is a safety measure to prevent damage to the washer and ensure optimal cleaning performance.
If you encounter the rL or F34 error code, follow these steps to resolve the issue:
- Open the washer door and carefully remove any items that may be blocking the drum.
- Check the drum thoroughly to ensure that all items have been removed.
- Close the washer door securely.
- Select the Clean Washer cycle on the control panel.
- Start the cycle and allow it to complete.
- Once the cycle is finished, check for any remaining error codes. If the rL or F34 code is no longer displayed, the issue has been resolved.
If the rL or F34 error code persists after removing the items and restarting the Clean Washer cycle, you may need to contact Maytag customer support for further assistance.
Sud or Sd Error Code
The Sud or Sd error code appears when there are too many suds in the washing machine. This can prevent the washer from spinning out water. To resolve this issue, follow these steps:
- Make sure you are using HE or High Efficiency detergent designed for your Maytag washer. Using the wrong detergent or using too much detergent can cause excessive suds.
- Avoid using “no splash” or “easy pour” liquid chlorine bleach, as these can also contribute to excessive suds.
- Check the drain hose and standpipe for any restrictions. A restricted drain hose can cause water to back up and result in the Sud or Sd error code.
If you continue to experience the Sud or Sd error code after following these steps, it may be necessary to contact Maytag customer service for further assistance.
Customer Review
“I recently encountered the Sud error code on my Maytag washer and was unable to get the machine to spin out the water. After checking the detergent I was using, I realized I had mistakenly used regular detergent instead of HE detergent. Once I switched to the correct detergent, the error code disappeared, and the washer worked perfectly. Lesson learned!” – Maria, satisfied Maytag customer
F5 E2 Error Code
The F5 E2 error code on your Maytag washer indicates a problem with the door not locking properly. This can prevent the washer from starting or continuing the cycle. If you’re experiencing this error, follow the steps below to troubleshoot and resolve the issue:
- Check for any items blocking the door. Sometimes, objects can get lodged in the door’s path, preventing it from closing completely. Clear away any obstructions and ensure that the door is able to close fully.
- Inspect the door latch to see if there are any signs of damage or wear. A faulty latch can cause the door not to lock properly. If you notice any issues, consider contacting a professional for repair or replacement.
- Try pressing the pause or cancel button twice and then press the power button once to clear the code. This can sometimes reset the washer and resolve minor glitches causing the door lock problem.
If the F5 E2 error code persists after following these steps, it’s recommended to contact Maytag customer support or schedule a service appointment. They can provide further assistance and ensure that your washer is functioning properly.
| Error Code | Possible Cause | Resolution |
|---|---|---|
| F5 E2 | Door not locking properly |
|
F7 E1 Error Code
The F7 E1 error code on your Maytag washer indicates a motor speed sensing error. This error can occur due to various reasons, but there are a few troubleshooting steps you can take to resolve it.
Firstly, check for any remaining shipping bolts that may have been left in place during installation. These bolts can impede the correct speed for the cycle selection and cause the error code to appear. Ensure that all shipping bolts have been removed and the washer is correctly balanced.
Additionally, make sure that the washer has not been overloaded with laundry. Overloading the washer can put extra strain on the motor, leading to a speed sensing error. Remove some items from the washer and redistribute the load evenly to see if the error code clears.
If the F7 E1 error code persists after performing these troubleshooting steps, try pressing the pause or cancel button twice and then press the power button once to clear the code. Restart the washer and see if the error code reappears. If it does, it may indicate a more complex issue that requires professional assistance.
“The F7 E1 error code indicates a motor speed sensing error.”
Troubleshooting Steps for F7 E1 Error Code
| Troubleshooting Steps | Description |
|---|---|
| Check for remaining shipping bolts | Remove any shipping bolts left in place during installation, as they can interfere with the motor speed. |
| Avoid overloading the washer | Ensure that the washer is not overloaded with laundry, as this can strain the motor and trigger the error code. |
| Press pause or cancel button | To clear the error code, press the pause or cancel button twice, followed by the power button once. |
| Seek professional assistance | If the error code persists after troubleshooting, it may indicate a more complex issue that requires professional repair. |
Remember, if you’re unable to resolve the F7 E1 error code or if it continues to recur, it’s always recommended to reach out to a professional technician or contact Maytag customer support for further assistance.
F8 E1 or LO FL Error Code
If you encounter the F8 E1 or LO FL error code on your Maytag washer, it is indicating a low flow of water. This can be a frustrating issue, but we have a few troubleshooting steps to help you resolve it.
First, check the water supply and ensure that both the hot and cold water faucets are turned on fully. Sometimes, a partially closed water valve can restrict the flow of water to the washer. Make sure the faucets are fully open to allow a sufficient water supply.
Next, verify that the water inlet hoses are properly connected and not kinked. A kinked hose can impede the flow of water and trigger the F8 E1 or LO FL error code. Inspect both the hot and cold water hoses for any bends or twists and straighten them if necessary.
If the issue persists, try pressing the pause or cancel button twice and the power button once to clear the error code. This can often reset the washer and resolve minor issues.
If you have followed these steps and the F8 E1 or LO FL error code still appears, it may indicate a more serious problem. In this case, it is recommended to contact the Maytag customer service or schedule a service appointment to have a professional technician diagnose and repair the issue.
Remember: Troubleshooting an error code is a great way to resolve minor issues with your Maytag washer, but if the problem persists or you are unsure about the troubleshooting steps, do not hesitate to seek professional assistance.
Continue reading to learn about other common Maytag washer error codes and their troubleshooting solutions.
F8 E2 Error Code
If you’ve encountered the F8 E2 error code on your Maytag washer, it indicates a problem with the dispenser system. This error code commonly occurs when the detergent drawer or cartridge is clogged with detergent residue. Fortunately, resolving this issue is relatively simple. Follow the steps below to troubleshoot and resolve the F8 E2 error code:
- Start by inspecting the detergent drawer or cartridge. Remove it from the washer and check for any visible clogs or buildup. If you notice any, clean the dispenser thoroughly using warm water and a mild detergent.
- Once you’ve cleaned the dispenser, reinsert it into the washer, ensuring it is properly aligned and securely in place.
- After reinserting the dispenser, run a test cycle to check if the error code has cleared. Select a regular wash cycle and monitor the dispenser during the cycle to ensure proper operation.
If the error code persists after following these steps, it may indicate a more significant issue with the dispenser system. In such cases, it is recommended to contact a professional technician or schedule a service appointment with Maytag for further assistance.
Note: Always refer to the owner’s manual for specific instructions and guidelines pertaining to your Maytag washer model.
Expert Tip:
“Regular maintenance of your Maytag washer’s dispenser system is crucial to prevent clogs and ensure optimal performance. Clean the dispenser regularly and avoid overfilling it with detergent or fabric softener.”
F9 E1 Error Code
The F9 E1 error code on your Maytag washer indicates that drain times are longer than expected. This error can occur due to various reasons, but by following a few troubleshooting steps, you can resolve the issue and get your washer back to optimal performance.
To begin, check the drain hose for any kinks or clogs that may be obstructing the water flow. Ensure that the hose is properly installed and not twisted or bent. A blocked or improperly installed drain hose can lead to longer drainage times.
Excessive suds can also cause delays in draining. It is important to use HE (High Efficiency) detergent specifically designed for front load washers. Using non-HE detergent or using too much detergent can create excessive suds that impede the draining process. Reduce the amount of detergent used and make sure to follow the manufacturer’s guidelines for proper detergent usage.
By examining and addressing these potential issues – checking the drain hose and using the correct detergent – you can resolve the F9 E1 error code on your Maytag washer and ensure that your laundry cycles run smoothly without longer than expected drain times.
FAQ
What does the LOC or LC error code mean?
The LOC or LC error code indicates that the control lock has been activated. To remove the code, touch the Control Lock button or consult your Owner’s Manual for the specific button on older models. If the code persists, try pressing and holding the button or unplugging the washer for a minute.
Why am I seeing the dET error code?
The dET error code appears when the detergent cartridge is not detected in the dispenser. If you are using single-load doses of detergent, you can ignore this message. Make sure the dispenser cartridge is inserted correctly and the drawer is shut completely.
What does the Int error code mean?
The Int error code indicates that the cycle was paused or canceled. The washer may take some time to stop spinning and drain, displaying this error code during that time. To remove the code, press the pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.
What do the rL or F34 error codes indicate?
The rL or F34 error codes indicate that items were detected in the washer during the Clean Washer cycle. Remove the items from the drum and restart the Clean Washer cycle to clear the code.
Why am I seeing the Sud or Sd error code?
The Sud or Sd error code appears when there are too many suds in the washing machine. This can prevent the washer from spinning out water. Make sure you are using HE or High Efficiency detergent and avoid using “no splash” or “easy pour” liquid chlorine bleach. Check for a restricted drain hose or standpipe as well.
What does the F5 E2 error code mean?
The F5 E2 error code indicates that the door is not locking properly. Check for any items blocking the door and ensure it is closing completely. Press the pause or cancel button twice and the power button once to clear the code.
What does the F7 E1 error code indicate?
The F7 E1 error code indicates a motor speed sensing error. Check for any remaining shipping bolts, as they may impede the correct speed for the cycle selection. Make sure the washer has not been overloaded. Press the pause or cancel button twice and the power button once to clear the code.
Why am I seeing the F8 E1 or LO FL error code?
The F8 E1 or LO FL error code indicates a low flow of water. Check the water supply and ensure that both the hot and cold water faucets are turned on fully. Verify that the water inlet hoses are properly connected and not kinked. Press the pause or cancel button twice and the power button once to clear the code.
What does the F8 E2 error code mean?
The F8 E2 error code indicates a problem with the dispenser system. Verify that the detergent drawer or cartridge is not clogged with detergent. Clean the dispensers if necessary.
Why am I seeing the F9 E1 error code?
The F9 E1 error code indicates that drain times are longer than expected. Check the drain hose for any kinks or clogs and ensure it is properly installed. Excessive suds may also cause delays in draining, so make sure you are using HE detergent.
Source Links
- https://fixappliances.ca/maytag-machine-error-codes-and-how-to-fix-them/
- https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers
- https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers