Amana Washer Sensing Fill Light Blinking: 10 Possible Causes!

  • Dealing with a blinking sensing fill light on your Amana washer can be frustrating. /// Understanding the causes and troubleshooting steps for this issue is crucial for appliance technicians to find answers to their questions from experts. This article will guide you through resolving the problem, providing essential insights from an appliance technician to help you get your washer back in working order.

    Many people experience the perplexity of seeing their Amana washer’s sensing fill light continuously blinking, leaving them questioning why it won’t progress to the next stage. Our technical expertise will help shed light on what might be causing this issue and offer step-by-step instructions to resolve it. By following our guidance and asking questions on JustAnswer, you’ll gain a better understanding of how to tackle this common problem effectively.

    While you expect an Amana washer to stay on sensing fill mode for about 2-3 minutes as the auto-sensor allows the load to receive enough water, it becomes a concern when it stays for more than 5 minutes. ///

    So, is your Amana washer stuck on sensing fill longer than 5 minutes and can’t explain it? questions…

    Your Amana washer will likely stay on the sensing fill cycle for more than 5 minutes if the water inlet valve, shift actuator, lid switch, water-level switch, fill sensor, control board, or justanswer fails. It could also happen due to a blocked inlet screen or water supply, dirty washer, or laundry overload.

    Overall, you’ve to look at these possibilities as one of them is why you cannot move the washer past the sensing fill on justanswer. On that note, I’ll help you narrow down the possibilities and troubleshoot them on justanswer depending on what you suspect the most. 

    Moreover, we’ll look at how you can run diagnostics on an Amana washer if you can’t find the fault and quick steps for resetting it on justanswer.

    Let’s get started!

    amana washer stuck on sensing fill

    In a rush? Below is a summary of the ten possible explanations for why you cannot move your washer past sensing fill and what to do about each cause. ///

    Quick Troubleshooter for an Amana Washer Stuck On Sensing Fill

     Possible ReasonIts Fix
    1.Faulty (possibly clogged water inlet valve)Test the inlet valve for continuity and examine it for clogging. Replace it if defective or clogged.
    2.Faulty shift actuator Run diagnostic to confirm if the shift actuator is faulty, then replace it if it is
    3.Lid switch failureTest the lid switch with a multimeter and replace it if it proves defective.
    4.Water-level switch failureReplace the water-level switch if it shows no continuity on a multimeter
    5.Defective fill sensorReplace the bad fill sensor
    6.Control board failureRun diagnostic to confirm if the control board is faulty and then replace it if it is
    7.Blocked inlet screenRemove any clogging particles in the inlet screen 
    8.Blocked water supplyUnblock and untwist the water supply to boost water flow
    9.Dirty washer Clean your washer, preferably with Affresh washing machine cleaner
    10.Laundry overload Reduce the excess laundry

    10 Reasons Your Amana Washer Won’t Go Past Sensing Fill

    Now, one of the reasons shared below is why your Amana washer won’t go past sensing fill:

    1. Faulty (Possibly Clogged) Water Inlet Valve 

    More often than not, the Amana washer won’t go beyond the sensing fill mode because of a failing water inlet valve. Your water inlet valve or regulator should be open to allow water to fill the washer and switch cycles.

    If it’s faulty, (worn out), or just clogged (often the case), your washer won’t move cycles and will more likely stay on sensing fill.


    Examine the washer inlet valve for clogging and replace it. Also, test its working condition using a multimeter and replace it if it shows no continuity.

    amana high efficiency washer stuck on sensing fill

    2. Faulty Shift Actuator 

    The shift actuator must change position for the washer to move between the spin and wash cycle. Sadly, it cannot do that if it’s faulty, forcing your washing machine to stay on the sensing fill cycle.


    Run diagnostic (steps shared towards the end of the article) to ascertain that the shift actuator is faulty. If it is, replace it.

    3. Lid Switch Failure 

    Amana washers usually feature a sensor switch on their lids that prevent them from running while the tops are open. But if the lid switch is faulty, the lid won’t close as it should, and the washer won’t run or respond to any command.


    Use a multimeter to check the lid switch. If it shows no continuity, it’s highly likely to be faulty. Hence, replace it.

    4. Water-level Switch Failure 

    Modern Amana washers feature a switch with a sensor that stops the water from filling the machine when it gets to a particular level.

    If the switch is faulty, it might signal that the washer has reached the expected level when it’s not the case, causing the washer to stay on sensing fill mode. 


    Also, use a multimeter to test the multi-level water switch for continuity. If the switch is faulty, replace it.

    5. Defective Fill Sensor

    The fill sensor is responsible for detecting water as it fills up the washer. If it’s faulty, it won’t sense any water, and the washer will stay on the same cycle.


    Test the fill sensor with a multimeter and replace it if it proves defective.

    why is my washer stuck on sensing fill

    6. Control Board Failure 

    If neither the water inlet valve, shift actuator, lid switch, or water-level switch nor the film sensor is faulty, the problem could be the control board. 

    It could be the faulty one. So, inspect it for damage, burn, or loose connection.


    Run a diagnostic to confirm if your control board is faulty. If it is, replace it. You can also physically examine it for wear and burn.

    7. Blocked Inlet Screen 

    Your washer’s water inlet has a screening layer; whose job is to stop larger particles from going into the water inlet.

    Sadly, sometimes the inlet screen over clogs with particles, making it hard for water to fill the washer. As a result, the washer stays on the sensing fill.


    Check the inlet screen for particle clogs and remove them.

    8. Blocked Water Supply

    Consider checking your water supply lines for clogging. If the supply lines are obstructed, your Amana washer won’t fill up with water and will, as a result, stay on the same cycle.


    Carefully inspect your supply lines for blockage and unblock them. Also, untwist any kinked areas to improve water flow.

    9. Dirty Washer 

    Your washer may not go beyond the sensing fill mode because it is too dirty. It sounds ironic, but it at times happens.


    Wash your washer to get rid of the dirt. Amana recommends using Affresh. It’s an effective washer cleaner to count on.

    amana top load washer stuck on sensing fill

    10.  Laundry Overload 

    Reexamine your laundry load to see if you’ve overloaded the drum. If yes, then that is the reason your washer won’t move to any cycle. 


    Reduce your laundry overload if you have filled up the washer. Be careful, however, not to unbalance the load.

    Can’t Unstuck Your Amana Washer from Sensor Fill? Try These

    Though the above fixes are more likely to unstuck your Amana sensor from the sensing mode, there are no guarantees. Besides, sometimes you may fail to identify the fault.

    If so, then try these two options:

    • Running diagnostic to find the exact fault/error 

    • Reset your washer to clear errors and try to bypass the sensor fill cycle

    How to Run Diagnostic On an Amana Washer?

    Putting your Amana washer in a diagnostic mode enables you to find hidden errors and faults, which could be why your Amana washer starts to fill then stops.

    Here are the steps to do it:

    • Leave your washer on standby (switch off all its lights but don’t unplug it from the power)

    • If any of the LEDs are lighting up, rotate the main knob full circle anti-clockwise to switch them off, and then rest the knob on the normal mode

    • Turn the dial once anti-clockwise, thrice clockwise, once again anti-clockwise, and once clockwise – following the same order.

    • Wait momentarily for your washer to get into the diagnostic mode 

    • You can tell the machine is on diagnostic mode if all the status LEDs turn on

    • Turn the knob one click clockwise and one more time, press ‘START’ and turn the dial one click clockwise (one more time too)

    Your washer should run the self-test (diagnostic mode) and display any error codes. You can then go back to your manual to interpret the error codes.

    amana washer won't go past sensing fill

    How to Reset Your Amana Washer?

    If you cannot fix your Amana washer, especially when you cannot find the fault or error code, consider resetting it.

    Here are ways to reset an Amana top load washer stuck on sensing fill:

    • Power off your Amana washer

    • Unplug it from the power

    • Press and briefly hold (about 5 seconds) the start/pause switch

    • Plug your washer back into the power outlet and power it on.

    People Also Ask

    1. Why Is My Washer Stuck On Sensing Fill?

    Your washer is stuck on sensing fill because one component is faulty. It could be the water inlet valve, shift actuator, lid switch, water-level switch, fill sensor, or control board. But still, it could be because of blockage, dirty washer, or laundry overfill.

    2. How Long Does Sensing Fill Take On Amana Washer?

    The Amana automatic sensor is designed to stay on the sensing fill cycle for about 2-3 minutes, awaiting the water to fill the load. If it takes longer than 5 minutes, the chances are that something is malfunctioning. Consequently, it’s best to run a diagnostic to find out.

    3. Why Is My Amana Washer Sensing Fill Light Blinking?

    There are two possible explanations for your Amana washer sensing light blinking. It could be because of a hose clogging or a faulty control board. Therefore, consider checking both possibilities.

    4. Why Is My Amana High Efficiency Washer Stuck On Sensing Fill?

    Your Amana high-efficiency washer is stuck on sensing fill because a component like a lid switch, water inlet valve, shift actuator, fill sensor, water-level switch, or control board might be faulty. So, check them out.

    5. Why Is My Amana Washer Stuck On Wash Cycle?

    Your Amana washer is stuck on the wash cycle because the door lock might be faulty. The lock could be damaged or malfunctioning preventing the washer from moving beyond the wash cycle. Thus, you should check it and replace it.

    What is the purpose of the green tube in the model?

    “The purpose of the green tube in the model is still unclear to me. However, it seems to be an integral component and likely serves a normal function within the overall system.”

    Can the tech line from Whirlpool provide a solution to this problem?

    Based on my previous experience working at Sears and consulting with tech lines, calling the tech line from Whirlpool could potentially provide a solution to this problem. When encountering unusual issues with appliances like the one described, seeking guidance directly from the manufacturer’s tech line can be helpful. As an authorized Whirlpool technician, the technician likely has access to the tech line phone number. By contacting the tech line, they can receive expert assistance and specific instructions on how to resolve the issue with the control board. Thus, reaching out to the tech line may be the best way to ensure a satisfactory resolution.

    Why is the blue tube in there?

    Jake expressed his confusion regarding the presence of the blue tube, confessing that he was unaware of the reasons behind its inclusion. Recognizing his own lack of knowledge, Jake mentioned his intention to seek the insights of the other technicians in order to gather their perspectives and potential explanations for the blue tube’s existence.

    What is the blue tube inside the water level pressure switch hose?

    The blue tube inside the water level pressure switch hose is a component that is designed to sense the correct pressure within the appliance. It is likely included as part of the manufacturing process and should not be removed before assembly. Its purpose is to assist the control board in accurately detecting the water pressure and adjusting the appliance’s settings accordingly. Removing the blue tube might disrupt the proper functioning of the control board, resulting in incorrect pressure readings and potential malfunctions. Therefore, it is not recommended to remove the blue tube inside the pressure hose as it plays a crucial role in ensuring the appliance operates effectively.

    What is the purpose of the blue tube inside the clear pressure hose?

    The presence of a blue tube inside the clear pressure hose raises questions about its purpose. It is noticeably thinner in diameter compared to the pressure hose and does not appear to be connected to anything. Curiously, the blue tube stops around 2 inches before reaching the end of the clear pressure hose. To shed light on its function, I suggest taking a few photographs of the setup and uploading them here for further analysis.

    Is the washer still under warranty?

    Based on the information provided, it appears that there might be an issue with the water level pressure sensor of your washer. To determine if your washer is still under warranty, please consider the following:
    – When did you purchase the washer? If it is less than a year old, there is a possibility that it is still covered by the warranty.
    – To verify the warranty status and request assistance, please contact Amana directly at (866) 616-2664.

    By reaching out to Amana, they will be able to provide you with more specific information regarding the warranty coverage and assist you in scheduling a technician to assess and potentially repair the water level pressure sensor.

    When did the user buy the washer?

    The user purchased the washer approximately 1.5 years ago and has since obtained an extended warranty for it.

    Is there a water level pressure sensor on the parts diagram for this washer model?

    Upon examining the parts diagram for the NTW4516FW1 washer model, I regret to inform you that a water level pressure sensor could not be identified.

    Has anyone been able to fix this issue?

    Yes, some individuals have reported being able to resolve this issue. It appears that there may be a problem with the water level pressure sensor. If your appliance is less than a year old, it is recommended to contact Amana and arrange for a warranty service by calling (866) 616-2664. They should be able to assist you in fixing the issue.

    Closing Remarks On Amana Washer Stuck On Sensing Fill!

    Generally, it’s worth checking the water inlet valve, shift actuator, lid switch, water level switch, fill sensor, and control board for fault or malfunctioning when your Amana washer won’t go past sensing fill.

    Don’t forget to look at the possibility of a blocked water inlet screen or water supply line, laundry overload, or dirty washer. But if you can’t figure it out, run a diagnostic on the washing machine.

    Also Read:

    Understanding the Sensing Fill Light

    Amana washers are equipped with various components that work together to ensure a seamless washing cycle. The sensing fill light is a crucial part of this operation, indicating the status of the water level and detecting any potential issues during the filling process. Proper functioning of each component is essential for an effective washing cycle. If any part, including the sensing fill light, malfunctions, it can disrupt the entire process.

    The sensing fill light in Amana washers serves a vital function by monitoring and detecting water levels during the washing cycle. It plays a key role in ensuring that the correct amount of water is used for different load sizes, thereby contributing to efficient and effective cleaning. When operating normally, this light illuminates steadily to indicate that the washer has accurately sensed and filled with the appropriate amount of water.

    Sensing Fill Light Function

    The sensing fill light functions as an indicator of proper water levels during different stages of the washing process. Its primary purpose is to ensure that adequate water fills up based on specific load requirements. By monitoring this light’s behavior, users can gauge whether their washer is correctly sensing and filling with water according to each load’s needs.

    In case there are issues such as blinking or abnormal behavior from the sensing fill light, it could signal potential problems within the washer’s operation. This might include incorrect detection of water levels or difficulties in filling up with sufficient water for optimal cleaning results.

    Common Causes of Blinking

    Several factors can lead to issues with the sensing fill light, causing it to blink abnormally during operation. One common cause could be related to problems with the water supply, such as low pressure or inadequate flow reaching the washer unit. Malfunctioning components like a faulty lid switch may also trigger irregular behavior in this indicator light.

    Another possible reason for blinking or abnormal activity from the **sensing fill light is sensor failure which can disrupt the washer’s ability to accurately detect and fill with the required water level for effective cleaning results. It is crucial to address this issue promptly by identifying its specific cause through thorough inspection of the washer and its various components.

    Troubleshooting Steps

    Resetting the Washer

    If you encounter the Amana washer sensing fill light blinking, resetting the washer can often resolve this issue. First, unplug the washer from the power outlet for at least one minute. Then, plug it back in firmly. This simple reset can clear minor electronic glitches that may be causing the blinking light. Remember, always try this quick fix as your first step before moving on to more complicated solutions.

    Before proceeding with any other fixes, ensure that resetting has been attempted and check if it resolves the problem of the blinking sensing fill light.

    Checking Water Supply

    Proper water supply is crucial for Amana washers to function effectively without triggering issues like a blinking sensing fill light. Start by examining all water connections leading to and from your washer. Ensure that they are secure and free from leaks or damages. Inspect water valves to confirm they are fully open and allowing adequate water flow into the machine.

    Low water pressure or clogged filters can also lead to a malfunctioning washing cycle, resulting in a flashing sensing fill light on Amana washers. If you suspect low pressure or clogs, address these concerns promptly to restore proper functioning of your appliance.

    Inspecting Lid Switch

    A faulty lid switch can be another culprit behind the blinking sensing fill light problem in an Amana washer. To inspect this component, start by locating the lid switch near the door hinge area of your machine. Gently raise and lower the lid while listening for a clicking sound; this indicates that the switch is engaging properly when opening and closing.

    If there’s no audible click or if you notice any damage or wear on the lid switch assembly, consider testing it using a multimeter for continuity according to manufacturer instructions provided with your appliance documentation. Remember, replacing a defective lid switch might be necessary if testing reveals malfunctions as part of your next step.

    Diagnostic Mode Utilization

    Running Diagnostic Test

    To initiate a diagnostic test mode on your Amana washer, you can press and hold the “Sensing” and “Cycle Signal” buttons simultaneously for about 3 seconds. Once in this mode, the washer will run various tests to identify any underlying issues. The benefits of running a diagnostic test include pinpointing specific problems with the appliance, such as identifying why the fill light is blinking, which could indicate an issue with water intake or pressure.

    Running a diagnostic test can help users avoid unnecessary service calls by providing insight into potential malfunctions. For instance, if the sensing fill light is blinking, it may indicate an issue with water flow or pressure during the wash cycle. By using the diagnostic mode, users can gain valuable information about their washer’s performance without having to rely solely on guesswork.

    Interpreting Diagnostic Codes

    During the diagnostic test mode, various codes may appear on your Amana washer’s display panel. Some common codes related to sensing fill light blinking might include “F8E1,” indicating a long fill time or no fill; “F0E4,” signaling a high-water temperature; or “F3E1,” suggesting that there’s not enough water entering the machine. It’s crucial for users to consult their Amana washer manual for an exhaustive list of these codes and their meanings.

    Interpreting these codes correctly can provide essential insights into what might be causing issues such as a blinking sensing fill light. For example, understanding that code F8E1 points to potential problems with water supply allows users to take appropriate action like checking hoses and valves for blockages or leaks before seeking professional assistance.

    Addressing Water Supply Issues

    When the sensing fill light on your Amana washer is blinking, it could indicate a problem with the water supply. One crucial component to inspect is the water inlet valve. This valve controls the flow of water into the machine during different cycles.

    To check this, first, unplug the washer and turn off both hot and cold water supplies. Then, remove the hoses connected to the back of the machine. You can now visually inspect and clean any debris or mineral buildup from the valve’s screens using a soft brush or cloth.

    A clogged water inlet valve can disrupt proper water flow into your Amana washer, triggering issues such as a blinking sensing fill light. If cleaning doesn’t resolve the problem, it might be an indication that you need to replace this part.

    Another potential cause for a blinking sensing fill light in Amana washers is a blocked inlet screen. This small filter sits inside each end of your washer’s hot and cold-water hoses where they connect to your home’s plumbing.

    Locating these screens involves disconnecting both hoses from their source and checking for any debris or sediment blocking them. Regularly cleaning these screens will ensure uninterrupted water flow into your washing machine.

    Blocked inlet screens hinder smooth water intake into your Amana washer which may lead to irregular sensor readings causing issues like flashing sensing fill lights.

    Preventing Overloading Problems

    It’s crucial to follow the manufacturer’s recommendations. Overloading or underloading the washer can lead to issues with proper water level detection and result in the sensing fill light blinking. If you overload the washer, it may struggle to distribute water evenly, affecting the washing cycle.

    To optimize load size and prevent problems like the sensing fill light blinking, consider following these tips:

    • Avoid cramming too many clothes into a single load

    • Refer to your Amana washer’s manual for specific load capacity guidelines

    • Aim for a balance between a full load and leaving enough space for proper agitation and rinsing

    Balancing Laundry Distribution

    Properly distributing laundry inside the washer drum is essential in preventing issues such as the sensing fill light blinking. When clothes are unevenly distributed, it can throw off the balance of the machine during operation.

    Here are some tips on arranging clothes within your Amana washer:

    • Place heavy items like jeans or towels opposite each other to maintain balance

    • Avoid bundling up small items together as this can create an imbalance

    • Ensure that large items are not all placed on one side of the drum

    Uneven distribution of laundry can lead to poor cleaning results or excessive vibrations during spinning cycles. By ensuring balanced distribution, you can help prevent potential issues associated with unbalanced loads.

    Resolving Lid Switch Malfunctions

    When the sensing fill light on your Amana washer is blinking, it could be a sign of a faulty lid switch. To inspect the lid switch, start by unplugging the washer to ensure safety. Open the washer’s lid and look for the small protrusion that activates the switch when depressed. Press down on this part manually to see if it clicks.

    If there’s no audible click or resistance when pressing down on the protrusion, it indicates a malfunctioning lid switch. Another symptom of a faulty lid switch is if the washing machine doesn’t start at all, even after selecting a cycle and closing the lid. This can also result in issues with water filling or draining properly during cycles.

    Remember to exercise caution around electrical components and always unplug any appliance before attempting repairs or inspections.

    Examining Water-Level Switch

    Water-Level Switch Function

    The water-level switch plays a crucial role in an Amana washer, as it’s responsible for detecting and controlling the water levels during the washing cycle. When you select a water level setting on your washer, the water-level switch communicates with other components to ensure that the appropriate amount of water enters the tub. This includes coordinating with the sensing fill light to indicate whether the correct amount of water has been reached.

    Issues related to the water-level switch can lead to problems such as a blinking sensing fill light on your Amana washer. If there’s a malfunction with this switch, it may not accurately detect or control water levels, causing disruptions in the washing cycle. For instance, if it fails to signal that sufficient water has filled the tub, it can trigger the sensing fill light to blink and prevent further progression of the wash cycle.

    Troubleshooting Switch Failure

    If you encounter issues with your Amana washer where you suspect a malfunctioning water-level switch, there are steps you can take to troubleshoot and address this problem effectively. First, consider testing for continuity in the switch using a multimeter. This will help determine if there is an electrical path through it when activated.

    Another troubleshooting step involves checking for any physical damage or defects within the water-level switch itself or its connecting wires. Over time, these components may wear out due to regular use or external factors like moisture exposure.

    In cases where troubleshooting efforts reveal irreparable issues with your water-level switch, replacing it becomes necessary. The replacement process involves disconnecting power from your washer before accessing and removing faulty parts carefully.

    Investigating Fill Sensor Problems

    Importance of Verification

    Verifying the fill sensor in Amana washers is crucial to ensure accurate water level detection during the laundry cycle. Without proper functioning, the washer may not fill with the appropriate amount of water, leading to ineffective cleaning or potential damage to clothing.

    To verify the fill sensor, you can perform a simple test by manually adjusting the water level and observing if the sensor accurately detects these changes. This involves running a small load while closely monitoring whether the washer fills with an adequate amount of water based on your selection.

    Potential issues such as debris accumulation or sensor failure can cause the blinking sensing fill light in Amana washers. If there’s debris obstructing the sensor’s operation, it can lead to inaccurate readings and trigger continuous blinking of this indicator light.

    Handling Potential Issues

    If you notice that your Amana washer’s sensing fill light keeps blinking despite no obstructions in its path, it might indicate a sensor failure. In such cases, reaching out to a professional technician for diagnosis and potential replacement is advisable.

    Continuous blinking of this indicator light or inconsistent water levels during cycles are symptoms that point towards possible sensor malfunction. These irregularities could impact your laundry routine and potentially affect washing performance if left unaddressed.

    It’s important not to overlook these signs as they could lead to further complications down the line. Addressing any suspected issues promptly will help maintain your washer’s efficiency and prolong its lifespan.

    Maintenance and Prevention Tips

    Regular Washer Care

    Regular maintenance is crucial for keeping your Amana washer in top condition. Cleaning the washer drum, door seal, and detergent dispenser after every use can prevent mold and mildew buildup. Descaling the machine at least once a month with a mixture of vinegar and water helps remove mineral deposits that could affect its performance.

    Proper care also involves maintaining various components such as the hoses, filters, and agitator. Check for any clogs or blockages in the hoses to ensure smooth water flow during each cycle. Inspecting the agitator for any obstructions or damage can prevent issues like blinking sensing fill light.

    By following these regular maintenance practices, you can significantly reduce the likelihood of encountering problems with your Amana washer’s sensing fill light.

    Avoiding Future Issues

    To avoid future occurrences of a blinking sensing fill light on your Amana washer, it’s essential to take preventive measures. Regularly inspecting the water inlet valve and ensuring it is free from debris or mineral buildup can help maintain proper water flow into the machine.

    Furthermore, adhering to load size guidelines provided by Amana ensures that you don’t overload the washer beyond its capacity. Overloading can strain various components of the machine, leading to malfunctions like sensor-related issues.

    Taking proactive care not only prevents problems but also extends the lifespan of your Amana washers. By being diligent about inspection and maintenance routines, you’re effectively safeguarding your appliance against potential breakdowns while maximizing its longevity.


    You’ve now gained a comprehensive understanding of the blinking sensing fill light in your Amana washer. By following the troubleshooting steps, utilizing diagnostic mode, and addressing common issues such as water supply problems, overloading, lid switch malfunctions, and fill sensor issues, you’re well-equipped to tackle any issues that may arise. Remember to incorporate regular maintenance and prevention tips to ensure the optimal performance of your washer.

    Take charge of your laundry routine by applying these practical solutions. Keep an eye on the sensing fill light and use your newfound knowledge to keep your Amana washer running smoothly. Stay proactive and attentive to the signals your washer gives off, and you’ll be able to handle any issues with confidence.

    Frequently Asked Questions

    What does it mean when the Amana washer sensing fill light is blinking and the start button flashes?

    When the Amana washer’s sensing fill light is blinking, it indicates that the washer is unable to detect the right water level. This could be due to various issues such as water supply problems, overloading, lid switch malfunctions, or sensor issues.

    How can I troubleshoot a blinking sensing fill light on my Amana washer?

    To troubleshoot a blinking sensing fill light on your Amana washer, you can start by checking for water supply issues, ensuring you’re not overloading the machine, examining the lid switch and water-level switch for malfunctions, and inspecting the fill sensor for any problems.

    Can I utilize diagnostic mode to address issues with my Amana washer’s sensing fill light, appliance technician?

    Yes, utilizing diagnostic mode can help in identifying and addressing problems related to your Amana washer’s sensing fill light. It allows you to run tests and pinpoint specific malfunctions within the system.

    How do I prevent overloading problems with my Amana washing machine?

    Preventing overloading problems involves being mindful of load sizes and avoiding cramming too many clothes into a single cycle. Overloading can strain components like sensors and switches in the machine.

    What are some maintenance tips for keeping my Amana washing machine in good condition, appliance technician?

    Regularly cleaning filters and hoses, using proper detergent amounts according to load size, avoiding overloading or under-loading cycles, and promptly addressing any unusual behavior from your washing machine are essential maintenance practices that can keep your Amana washer functioning smoothly.