Clicky

Deciphering Whirlpool Error Codes: Quick Guide

When your Whirlpool appliance displays an error code, it can be frustrating and confusing to understand what it means. However, error codes are designed to provide valuable diagnostic information that can help you quickly identify and resolve issues with your appliances. In this quick guide, we will help you decipher and troubleshoot Whirlpool error codes effectively, so you can get your appliances back up and running in no time.

Key Takeaways

  • Whirlpool error codes provide valuable diagnostic information for troubleshooting appliance issues.
  • Understanding the meaning behind error codes can help you quickly address and resolve problems.
  • Consulting your Whirlpool appliance’s owner’s manual can provide specific error code information for your model.
  • If you’re unsure about a specific error code or unable to resolve the issue, it’s recommended to consult a professional technician.
  • Regular maintenance and proper installation can help prevent error codes and prolong the lifespan of your Whirlpool appliances.

Common Whirlpool Error Codes for Top Load Washers

whirlpool top load washer

If you own a Whirlpool top load washer, it’s essential to familiarize yourself with common error codes. These error codes can provide valuable insight into the underlying issues affecting your washer’s performance. By understanding the meaning behind these error codes, you can effectively troubleshoot and resolve any problems that arise.

  1. Error Code “drn”: This error code indicates that your washer is not draining properly. There could be a clog in the drain hose or a malfunctioning drain pump. Check the drain hose for any obstructions and ensure that it is installed correctly. Additionally, inspect the drain pump for any clogs or damage.
  2. Error Code “LdL”: This error code signifies that the lid of your washer is not locking properly. It’s crucial to ensure that the lid is not blocked by any items and that it can fully close. If the lid is obstructed or damaged, it may need to be repaired or replaced.
  3. Error Code “LF, Lo FL, or F8 E1”: This error code indicates that your washer is taking too long to fill with water. This could be due to water supply issues, such as low water pressure or a faulty inlet valve. Check your water supply connections and make sure that the water valves are fully open.

By following the suggested resolutions for each error code, you can effectively troubleshoot and resolve the problem with your Whirlpool top load washer.

Error Codes in Whirlpool Front Load Washers

whirlpool front load washer

If you own a Whirlpool front load washer, you may encounter error codes that can indicate various issues. Understanding these error codes is essential for troubleshooting and resolving problems efficiently. Here are some common error codes that you may encounter:

  1. LOC or LC: This error code indicates that the control lock is activated. To resolve this issue, you need to deactivate the control lock by pressing and holding the “Control Lock” button for three seconds.
  2. dET: If you see this error code, it means that the detergent cartridge is not detected. Ensure that the cartridge is properly inserted into the dispenser and that there are no obstructions.
  3. Sud: Excessive suds can lead to this error code. It is crucial to use the correct amount of high-efficiency (HE) detergent to prevent excessive suds. Remove excess suds and run a rinse cycle to resolve this issue.

To address these error codes, you can take the following steps:

  1. Check the door lock latch to ensure it is functioning properly. Clean any debris or obstructions that may hinder proper locking.
  2. Inspect the detergent dispenser for any clogs or blockages. Clean the dispenser thoroughly to ensure proper dispensing of detergent.
  3. Use high-efficiency (HE) detergent specifically designed for front load washers. Using regular detergent may lead to excessive suds and trigger error codes.

By performing these troubleshooting steps, you can resolve common error codes in Whirlpool front load washers and ensure smooth operation of your appliance.

Understanding Whirlpool Washing Machine Error Codes

whirlpool washing machine error codes

Whirlpool washing machines are equipped with error codes that help identify and diagnose issues with the appliance. These error codes can be divided into two categories: active error codes and stored error codes.

Active error codes are displayed immediately on the machine’s control panel when a problem is detected. They provide real-time information about the specific issue that needs attention.

Stored error codes, on the other hand, are codes that can be accessed through the machine’s diagnostic mode and are useful for troubleshooting purposes. They are stored in the machine’s memory and can help identify recurring or persistent issues.

Whirlpool washing machine error codes cover various categories, including water-related errors, spin-related errors, temperature-related errors, and more. These error codes serve as a valuable tool to help users and technicians pinpoint the specific problem that needs to be addressed.

By understanding these error codes, users can effectively identify and resolve issues with their Whirlpool washing machines. Whether it’s a water inlet problem, a drainage issue, or a malfunctioning component, the error codes provide guidance for quick and accurate troubleshooting.

In the next section, we will delve deeper into some specific error codes found in Whirlpool washers and explore troubleshooting steps to resolve them.

Common Error Categories in Whirlpool Washers

Error CategoryDescription
Water-related errorsIssues related to water inlet, water level, or water drainage
Spin-related errorsProblems with the spin cycle, including unbalanced loads or motor malfunctions
Temperature-related errorsErrors related to the temperature of the water or the overall heating system
Control-related errorsMalfunctions in the control panel or communication between components
Etc.Additional error categories specific to certain models or features

Decoding Whirlpool Washer Error Code F21

whirlpool error code F21

The F21 error code is one of the most common error codes in Whirlpool washers and indicates a drainage problem. This error can be caused by a clogged or improperly installed drain hose, a malfunctioning drain pump, or other issues. By checking the drain hose, cleaning the drain pump, and ensuring proper installation, you can troubleshoot and resolve the F21 error code in your Whirlpool washer.

Common Causes of F21 Error Code

The F21 error code in Whirlpool washers can occur due to the following reasons:

  • Clogged or improperly installed drain hose
  • Malfunctioning drain pump
  • Issues with the washer’s internal components

Troubleshooting the F21 Error Code

To troubleshoot and resolve the F21 error code in your Whirlpool washer, follow these steps:

  1. Check the drain hose: Ensure that the drain hose is not clogged or kinked. Straighten any kinks and remove any obstructions that may be blocking the flow of water.
  2. Clean the drain pump: The drain pump may be clogged with debris. Disconnect the washer from the power source and remove the front panel to access the pump. Clean out any debris and ensure that the impeller is not blocked.
  3. Inspect internal components: Check the drain pump filter and the pressure switch for any signs of damage or malfunction. Replace these components if necessary.
  4. Ensure proper installation: Verify that the drain hose is correctly installed and securely connected to the washer and the drain system. Make any necessary adjustments or repairs.

If the F21 error code persists after performing these troubleshooting steps, it is recommended to consult a professional technician or contact Whirlpool customer support for further assistance.

Troubleshooting Whirlpool Error Code F22 and F5 E3

Troubleshooting Whirlpool Error Code F22 and F5 E3

When faced with error codes F22 and F5 E3 in your Whirlpool washer, it is likely that you are experiencing door lock issues. These error codes typically appear when the door fails to lock properly or when there are obstructions preventing it from unlocking.

To troubleshoot and resolve these error codes, you can follow these steps:

  1. Check the door latch or lock: Inspect the door latch or lock to ensure that it is functioning correctly. Look for any signs of damage or misalignment that may be preventing the door from locking or unlocking properly.
  2. Inspect for obstructions: Examine the door and the surrounding area for any obstructions that may be hindering the door’s movement. Clear away any objects or debris that may be blocking the door.
  3. Ensure proper alignment: Make sure that the door is properly aligned with the washer. If it appears misaligned, adjust it accordingly to ensure proper locking and unlocking.

By following these troubleshooting steps, you should be able to address and resolve the F22 and F5 E3 error codes in your Whirlpool washer, allowing for smooth operation and efficient cleaning of your laundry.

Error CodeCauseResolution
F22Door not locking properlyCheck door latch or lock for damage or misalignment. Inspect for obstructions and ensure proper alignment with the washer.
F5 E3Door not unlocking properlyCheck door latch or lock for damage or misalignment. Inspect for obstructions and ensure proper alignment with the washer.

Troubleshooting Whirlpool Washer Error Code F20

The F20 error code in Whirlpool washers indicates water inlet problems, such as a blocked inlet or insufficient water supply. This can be caused by a variety of factors, including a kinked or clogged water hose, blocked inlet hose screens, or water supply valves not fully open. To troubleshoot and resolve the F20 error code in your Whirlpool washer, follow these steps:

  1. Inspect and clean the water hoses: Check the water hoses connected to your washer for any kinks or clogs. Straighten out any kinks and remove any debris or blockages that may be obstructing the water flow.
  2. Check the inlet screens: The inlet hose screens, located in the water inlet valve, can become clogged over time. Carefully remove the hoses from the water inlet valve and inspect the screens for any debris or mineral deposits. Clean the screens thoroughly before reattaching the hoses.
  3. Ensure proper water supply: Make sure that the water supply valves connected to your washer are fully open. In some cases, valves may not be turned on fully, restricting the water flow. Turn the valves clockwise to ensure they are completely open.

If the above steps do not resolve the F20 error code, it is recommended to consult the Whirlpool user manual or contact a professional technician for further assistance.

Common Causes of F20 Error Code:

CauseDescription
Kinked or Clogged Water HoseA hose obstruction or bent hose can impede water flow, leading to the F20 error
Blocked Inlet Hose ScreensMineral deposits or debris can accumulate on the inlet hose screens, reducing water intake
Insufficient Water SupplyThe water supply valves may not be fully open, restricting the water flow into the washer

“I encountered the F20 error code on my Whirlpool washer, and it turned out to be a kinked water hose. After straightening the hose, my washer began functioning properly again.” – Sarah R.

Addressing Whirlpool Washer Error Code F03 E01

The F03 E01 error code in Whirlpool washers indicates a water level detection problem. This error code can be frustrating, but it can be resolved with some troubleshooting steps. The issue is typically caused by a faulty water level pressure switch or connected components.

To troubleshoot the F03 E01 error code in your Whirlpool washer, follow these steps:

  1. Inspect the pressure sensor hose: Check the pressure sensor hose for any clogs or damage. Clear any debris that may be blocking the hose to ensure proper water level detection.
  2. Reset the control board: Resetting the control board can sometimes resolve the error code. Turn off the washer and unplug it from the power source for a few minutes. Then, plug it back in and turn it on to see if the error persists.
  3. Check for faulty components: If the error code continues to appear, there may be an issue with the water level pressure switch or other connected components. It’s recommended to consult a professional technician or contact Whirlpool customer support for further assistance.

By following these troubleshooting steps, you can address and resolve the F03 E01 error code in your Whirlpool washer, ensuring it operates smoothly and efficiently.

Whirlpool Washer Error Code F03 E01 Troubleshooting

“The F03 E01 error code in Whirlpool washers indicates a problem with water level detection.”

If you encounter the F03 E01 error code, it’s essential to inspect the pressure sensor hose for any clogs or damage. This simple step can often resolve the issue. Additionally, resetting the control board can help reset the system and clear any temporary errors. However, if the error code persists, it may indicate a faulty water level pressure switch or other connected components. In such cases, it’s best to seek professional assistance to ensure an accurate diagnosis and proper repair.

Troubleshooting Whirlpool Washer Error Code 5d, Sd, or Sud

The 5d or Sud error code in Whirlpool washers indicates excessive suds. This can be caused by using regular detergent instead of HE detergent, using too much detergent, or a clogged drain system. To troubleshoot and resolve the 5d or Sud error code in your Whirlpool washer, follow these steps:

  1. Switch to HE detergent: High-Efficiency (HE) detergents are specifically designed for modern washers, creating fewer suds and preventing them from accumulating. Use the recommended amount of HE detergent according to the product instructions.
  2. Use the correct amount of detergent: Using too much detergent can lead to excessive suds and trigger the 5d or Sud error code. Follow the manufacturer’s guidelines and measure the appropriate amount of detergent for each load.
  3. Check for clogs in the drain system: A clogged drain system can contribute to the formation of excessive suds. Inspect the drain hose for any obstructions or kinks that may impede proper water flow. Clean out any debris or residues that may be blocking the drain.

By following these troubleshooting steps, you can effectively address the 5d or Sud error code in your Whirlpool washer and ensure smooth and efficient operations.

Resolving Whirlpool Washer Error Code E1 F9

If you’re facing the E1 F9 error code on your Whirlpool washer, it indicates a long drain time. This issue can disrupt your laundry routine and leave you wondering how to resolve it. However, with some troubleshooting steps, you can effectively tackle the problem and get your washer back in working condition.

Possible Causes of the E1 F9 Error Code

The E1 F9 error code can occur due to a few common reasons:

  • A kinked drain hose: Make sure the drain hose is not twisted or obstructed.
  • Incorrect installation of the drain hose: Ensure the drain hose is properly connected and positioned at the correct height.
  • A clogged drain pump: Check if debris or lint has accumulated in the drain pump, impeding proper drainage.

Troubleshooting Steps for the E1 F9 Error Code

To resolve the E1 F9 error code in your Whirlpool washer, follow these simple steps:

  1. Check the drain hose: Inspect the drain hose for any kinks or blockages. Straighten the hose if necessary and remove any obstructions.
  2. Ensure proper installation: Verify that the drain hose is installed correctly, with no bends or loops that could restrict water flow.
  3. Clean the drain pump: Locate the drain pump and clean out any debris or lint that may have accumulated. Refer to your user manual for specific instructions on accessing and cleaning the drain pump.

By following these troubleshooting steps, you can address the E1 F9 error code in your Whirlpool washer and restore its optimal functionality. If the issue persists or you require further assistance, it’s recommended to consult a professional technician.

Error CodeCauseTroubleshooting Steps
E1 F9Long drain time
  • Check the drain hose for kinks or blockages.
  • Ensure proper installation of the drain hose.
  • Clean the drain pump from debris or lint.

Understanding Whirlpool Washer Error Code PF

The PF error code in Whirlpool washers indicates a power failure interrupting the wash cycle. This can occur due to a power outage or other electrical issues. When the washer experiences a power failure, it stops mid-cycle and displays the PF error code.

To troubleshoot and resolve the PF error code in your Whirlpool washer, follow these steps:

  1. Press start or power button: Start by pressing the start or power button to restart the washer cycle. In some cases, the error code may be cleared and the appliance can resume normal operation.
  2. Reset the display: If pressing the start or power button doesn’t resolve the PF error code, try resetting the display. Locate the control panel or display of your Whirlpool washer and look for a reset button or option. Consult your owner’s manual for specific instructions on how to reset the display.

By following these troubleshooting steps, you can resolve the PF error code and get your Whirlpool washer back up and running. If the error persists or if you’re unsure about performing any troubleshooting steps, it’s recommended to consult a professional technician for assistance.

Note: The image above illustrates the PF error code on a Whirlpool washer display.

Conclusion

Understanding and troubleshooting Whirlpool error codes is crucial for effectively addressing appliance problems. By following the suggested resolutions for each error code and consulting your owner’s manual for specific codes related to your model, you can keep your Whirlpool appliances running smoothly. It is important to prioritize safety throughout the troubleshooting process and seek professional help if needed.

Whether you encounter error codes in your top load or front load washers, understanding their meanings and underlying causes is the first step towards resolving the issues. By taking the time to inspect and clean components, such as drain hoses, door locks, water inlets, and drain pumps, you can often resolve the errors without the need for professional assistance.

If you are unsure about how to troubleshoot or fix the error codes for your Whirlpool appliance, it is always recommended to consult a professional technician. They have the expertise and knowledge to diagnose and repair complex issues, ensuring the optimal performance of your Whirlpool appliance and minimizing the risk of further damage.

FAQ

What should I do if my Whirlpool top load washer displays the “drn” error code?

The “drn” error code indicates that your washer is not draining properly. To troubleshoot this issue, check for any clogs or kinks in the drain hose, ensure that the drain hose is installed correctly, and inspect the drain pump for any malfunctions.

What does the “LdL” error code mean on my Whirlpool top load washer?

The “LdL” error code stands for “lid not locking.” This means that the lid of your washer is not locking properly. Inspect the lid for any obstructions and make sure that it is securely closed before starting a wash cycle.

Why is my Whirlpool top load washer displaying the “LF, Lo FL, or F8 E1” error code?

The “LF, Lo FL, or F8 E1” error code indicates that your washer is taking too long to fill with water. This can be caused by issues with the water supply, such as low water pressure or a blocked inlet hose. Check that the water supply valves are fully open and that the inlet hose screens are not clogged.

How can I address the “LOC or LC” error code on my Whirlpool front load washer?

The “LOC or LC” error code means that the control lock on your washer is activated. To resolve this issue, press and hold the “Control Lock” button for three seconds to disable the control lock feature.

What should I do if my Whirlpool front load washer displays the “dET” error code?

The “dET” error code indicates that the detergent cartridge in your washer is not detected. Make sure that the detergent cartridge is properly inserted and locked into place.

Why does my Whirlpool front load washer show the “Sud” error code?

The “Sud” error code indicates excessive suds in your washer. This can be caused by using regular detergent instead of high-efficiency (HE) detergent or using too much detergent. Switch to using HE detergent and reduce the amount used to resolve this issue.

How do I access the stored error codes in my Whirlpool washing machine?

You can access the stored error codes in your Whirlpool washing machine by entering the diagnostic mode. Consult your owner’s manual or the manufacturer’s website for instructions specific to your model.

What is the most common error code in Whirlpool washers?

The F21 error code is one of the most common error codes in Whirlpool washers. It indicates a drainage problem. To fix this issue, check the drain hose for clogs or improper installation and clean the drain pump.

How can I troubleshoot the F22 and F5 E3 error codes in my Whirlpool washer?

The F22 and F5 E3 error codes indicate door lock issues. To troubleshoot these errors, check the door latch or lock for any obstructions and ensure proper alignment. Remove any items that may be blocking the door from closing or opening.

What should I do if my Whirlpool washer shows the F20 error code?

The F20 error code indicates water inlet problems, such as a blocked inlet or insufficient water supply. Check the water hoses for any kinks or clogs, inspect the inlet hose screens for blockages, and ensure that the water supply valves are fully open.

How can I address the F03 E01 error code in my Whirlpool washer?

The F03 E01 error code indicates a problem with water level detection. Inspect the pressure sensor hose for any clogs or damage, check the connected components, and reset the control board. If the issue persists, contact a professional technician for further assistance.

What should I do if my Whirlpool washer displays the 5d or Sud error code?

The 5d or Sud error code indicates excessive suds in your washer. To resolve this issue, switch to using high-efficiency (HE) detergent, follow the proper dosage guidelines, and check the drain system for any clogs.

How can I troubleshoot the E1 F9 error code in my Whirlpool washer?

The E1 F9 error code indicates a long drain time. Check the drain hose for any kinks or obstructions, ensure that the drain hose is installed correctly, and clean the drain pump to resolve this issue.

What should I do if my Whirlpool washer shows the PF error code?

The PF error code indicates a power failure that interrupted the wash cycle. Press the start or power button to restart the washer cycle or reset the display to clear the error code.

Source Links