Clicky

Troubleshooting Frigidaire Gallery Dishwasher Codes

If you own a modern Frigidaire Gallery dishwasher, you may encounter error codes that indicate specific issues with your appliance. These error codes can be helpful in identifying and troubleshooting problems, ensuring your dishwasher operates at its best. In this article, we will guide you through the most common Frigidaire dishwasher error codes and provide troubleshooting tips to help you resolve these issues.

Key Takeaways:

  • Understanding Frigidaire Gallery dishwasher error codes is essential for troubleshooting issues with your appliance.
  • The most common error codes include PF (power failure), HO (heat delay), LO (low rinse aid), and CL (door not closed).
  • Troubleshooting steps for error codes involve checking power supply, water temperature, rinse aid dispenser, and door switches.
  • If the issue persists, consider seeking professional assistance.
  • Always refer to the manufacturer’s manual for specific troubleshooting instructions and safety precautions.

PF Error Code

Frigidaire dishwasher error code solutions

If you encounter the PF error code on your Frigidaire dishwasher, it indicates a power failure, typically caused by a significant drop in power, usually 10% or more. To address this issue, follow these steps:

  1. Check the voltage: Ensure that the voltage going into the dishwasher is sufficient. Low voltage can lead to power failure issues.
  2. Reset the dishwasher: If the voltage is adequate, try resetting the dishwasher by either turning off the power for five minutes or pressing the cancel button until the error clears.
  3. Troubleshooting: If the error code persists, further troubleshooting may be necessary. Refer to the dishwasher’s manual for specific troubleshooting steps or seek professional help.

If you’re unable to resolve the PF error code on your own, it’s recommended to contact a professional for assistance. They have the expertise to diagnose and fix complex issues with your Frigidaire dishwasher.

HO Error Code

Frigidaire dishwasher error code chart

The HO error code is commonly encountered in older Frigidaire dishwashers. It indicates that the water is either taking a long time to heat up or that the temperature is too low. To address this issue, follow the troubleshooting steps below:

  1. Start by running hot water in your sink before starting the dishwasher. This helps flush out any cold water from the lines, allowing the dishwasher to receive hot water more quickly.
  2. If the problem persists, it indicates a problem with the water heating system. You will need to troubleshoot this to determine the cause and find a solution.

If you are unsure how to troubleshoot the water heating system or if the issue persists after troubleshooting, it is recommended to seek professional assistance for further diagnosis and repair.

Troubleshooting the Water Heating System:

To troubleshoot the water heating system, you can perform the following steps:

  1. Ensure that the dishwasher is receiving an adequate supply of water. Check for any kinks or blockages in the water supply line that may be restricting the water flow.
  2. Inspect the dishwasher’s heating element for signs of damage or malfunction. If the heating element is faulty, it may need to be replaced.
  3. Check the dishwasher’s thermostat for proper functioning. A malfunctioning thermostat can result in water not heating up to the desired temperature.

If you have identified any issues during the troubleshooting process or if you are still experiencing the HO error code, it is recommended to contact a professional appliance technician for further assistance and repair.

Refer to the chart above for a comprehensive Frigidaire dishwasher error code guide that includes the meanings and troubleshooting steps for various error codes.

LO Error Code

Frigidaire dishwasher error code chart

The LO error code on your Frigidaire dishwasher indicates that the rinse aid dispenser needs to be filled. This error code is a simple reminder to refill the rinse aid dispenser to ensure optimal performance.

You can easily resolve this issue by following these steps:

  1. Locate the rinse aid dispenser on your dishwasher.
  2. Open the dispenser door.
  3. Refill the rinse aid dispenser with the appropriate rinse aid product, following the manufacturer’s instructions.
  4. Close the dispenser door securely.

Refilling the rinse aid dispenser will help to improve the rinsing and drying effectiveness of your dishwasher, ensuring that your dishes come out sparkling clean. Regularly checking and refilling the rinse aid dispenser will prevent the LO error code from appearing and maintain the efficiency of your Frigidaire dishwasher.

Additional Tips:

• Use high-quality rinse aid to optimize the performance of your dishwasher.

• Avoid overfilling the rinse aid dispenser, as this can lead to excess foaming.

• If the LO error code persists even after refilling the rinse aid dispenser, it is recommended to consult the Frigidaire troubleshooting guide or contact a professional for further assistance.

CL Error Code

Frigidaire dishwasher door not closed

The CL error code indicates that the control board is detecting that the dishwasher door is not closed. This error commonly occurs due to a misalignment or malfunction of the dishwasher door.

To address this issue, follow these steps:

  1. Check the Door: Ensure that the dishwasher door is properly closed. Sometimes, a slight adjustment or gentle push may be necessary to fully close the door.
  2. Inspect the Door Switches: The door switches play a crucial role in detecting whether the door is closed. Carefully inspect the door switches for any signs of damage or misalignment. If any issues are found, consider replacing the faulty switches.
  3. Inspect the Wiring: Examine the wiring connections between the door switches and the main control board. Look for any loose or damaged wires that may be disrupting the proper functioning of the dishwasher. If any faults are detected, repair or replace the wiring as necessary.

If the CL error code persists after performing these troubleshooting steps, it is recommended to consider replacing the main control board. This will ensure that all components of the dishwasher are functioning properly and minimize the chances of encountering further error codes.

Error CodeMeaningSolution
CLDishwasher door not closed
  • Check the door and ensure it is properly closed.
  • Inspect the door switches for any damage or misalignment.
  • Examine the wiring between the door switches and the main control board for faults.
  • If the issue persists, consider replacing the main control board.

rA Error Code

Frigidaire dishwasher error code rA

In the Frigidaire dishwasher error code list, the rA error code signifies a rinse aid switch failure. This error occurs when the dishwasher fails to detect the proper functioning of the rinse aid switch, which affects the dispensing of rinse aid during the wash cycle. If you encounter this error, follow the solutions below to resolve the issue.

  1. Refill the Rinse Aid Dispenser: First and foremost, check the rinse aid dispenser and ensure it is adequately filled with rinse aid. Properly filling the dispenser helps maintain effective rinsing and drying of dishes.

  2. Inspect the Wiring: If refilling the rinse aid dispenser doesn’t solve the problem, the next step is to inspect the wiring between the dispenser and the main control board. Look for any faults or loose connections that may be causing the rinse aid switch failure. If necessary, seek professional assistance to repair or replace the faulty wiring.

  3. Replace the Main Control Board: Should the error persist after checking the wiring, it might be necessary to replace the main control board. A malfunctioning control board can cause various error codes, including the rA error code. Consult a technician or contact Frigidaire customer support for guidance on replacing the main control board.

By following these Frigidaire dishwasher error code solutions, you can effectively troubleshoot and resolve the rA error code on your Frigidaire dishwasher.

i10 Error Code

The i10 error code on your Frigidaire dishwasher indicates a low water level problem. If you encounter this error, there are a few troubleshooting steps you can follow to resolve the issue.

First, check the water supply line for any kinks or blocks that may be restricting water flow. Ensure that the water supply faucet is turned on and providing an adequate water supply to the dishwasher.

If the water supply line appears to be clear and the faucet is fully open, you may need to inspect the dishwasher’s water inlet valve. This valve controls the flow of water into the dishwasher. Check for any blockages or damage that may be causing a decrease in water level. If necessary, clean or replace the water inlet valve to restore proper water flow.

By addressing these potential issues, you can troubleshoot the i10 error code on your Frigidaire dishwasher and ensure that it operates efficiently.

In the next section, we will discuss the common error codes i20, i40, and iF0, which indicate a restricted drain line or clogged filters and provide solutions to address these issues.

i20, i40, and iF0 Error Codes

The i20, i40, and iF0 error codes are indicators of a restricted drain line or clogged filters in your Frigidaire dishwasher. If you encounter any of these error codes, it’s important to address the issue promptly to ensure proper drainage and functionality of your dishwasher.

To troubleshoot these error codes, follow these steps:

  1. Check the drain hose for any blockages or kinks. Ensure that the hose is properly connected and free from obstructions that may impede water flow.
  2. Clean out the filters and the area around the sump. Remove any debris or residue that may be obstructing the drainage system. Rinse the filters thoroughly to remove any trapped particles.
  3. Inspect the garbage disposal and make sure that the knockout plug has been removed. This plug needs to be removed to allow the dishwasher to drain properly into the disposal.

By following these troubleshooting steps, you can address the i20, i40, and iF0 error codes in your Frigidaire dishwasher. However, if the problem persists or you are unsure of how to proceed, it’s recommended to seek professional assistance for further diagnosis and repair.

i30 Error Code

The Frigidaire dishwasher error code i30 indicates that there is water leaking into the base of the dishwasher. This issue can lead to potential damage to the appliance and surrounding areas if not addressed promptly. Fortunately, there are steps you can take to resolve this problem and prevent further leaks.

To troubleshoot the i30 error code, follow these steps:

  1. Check the pressure sensor: The pressure sensor is responsible for detecting water levels in the dishwasher. Over time, debris can accumulate and clog the sensor, causing it to malfunction. Inspect the pressure sensor and clean it thoroughly to remove any debris or blockages.
  2. Inspect the water inlet valve: The water inlet valve controls the flow of water into the dishwasher. It’s possible that the valve may be blocked or damaged, leading to a leak. Examine the water inlet valve for any signs of blockages or damage. If necessary, clean or replace the valve to ensure proper functioning.
  3. Ensure proper drain pump operation: A faulty or obstructed drain pump can contribute to water leakage in the base of the dishwasher. Check the drain pump to ensure it is working correctly and that there are no obstructions blocking the drain pump impeller. Clear any debris or foreign objects and test the drain pump to ensure it is functioning as expected.
  4. Check the dishwasher level: An improperly leveled dishwasher can cause water to pool and leak. Ensure that your dishwasher is level by using a leveling tool or adjusting the feet of the appliance. This simple step can help prevent water leakage and improve overall dishwasher performance.

“Proper maintenance and regular inspection of your Frigidaire dishwasher can help prevent and resolve error codes like i30. By addressing leaks promptly and ensuring the proper functioning of components, you can keep your dishwasher operating efficiently.”

Conclusion

Frigidaire Gallery dishwashers are equipped with error code systems that can be invaluable in troubleshooting common issues. By understanding the meaning behind these error codes and following the recommended solutions, many problems can be resolved without the need for professional assistance. However, if you are unsure of how to proceed or if the issue persists, it is always advisable to seek expert help.

When troubleshooting your Frigidaire dishwasher, it is important to refer to the manufacturer’s manual for specific troubleshooting steps and safety precautions. This will ensure that you handle and resolve the issues correctly, avoiding any potential risks. Remember, safety should always be a priority.

Familiarizing yourself with the Frigidaire dishwasher error code list will save you time and money in diagnosing and fixing problems. Be proactive in maintaining your dishwasher by cleaning filters, checking for blockages, and following the recommended maintenance schedule. Regular maintenance can help prevent the occurrence of error codes and keep your dishwasher running smoothly.

FAQ

What are some common Frigidaire Gallery dishwasher error codes?

Some common Frigidaire Gallery dishwasher error codes include PF (power failure), HO (heat delay), LO (low rinse aid), and CL (door not closed).

How can I troubleshoot a PF error code?

To troubleshoot a PF error code, first check the voltage going into the dishwasher and ensure it is sufficient. If the voltage is adequate, try resetting the dishwasher by turning off the power for five minutes or pressing the cancel button until the error clears. If the error persists, further troubleshooting or professional help may be necessary.

What does an HO error code indicate?

An HO error code indicates that the water is taking a long time to heat up or that the temperature is too low. To address this issue, run the hot water in your sink before starting the dishwasher to flush out any cold water from the lines. If the problem persists, further troubleshooting of the water heating system may be required.

How can I resolve an LO error code?

An LO error code indicates that the rinse aid dispenser needs to be filled. Simply refill the rinse aid dispenser according to the manufacturer’s instructions to ensure proper rinsing and drying of your dishes.

What should I do if I see a CL error code?

If you see a CL error code, first check that the dishwasher door is properly closed. If the door is closed but the error persists, check the door switches to ensure they are functioning correctly. Inspect the wiring between the door switches and the main control board for any faults. If the issue cannot be resolved, consider replacing the main control board.

How can I fix an rA error code?

To fix an rA error code, first refill the rinse aid dispenser. If the error persists, check the wiring between the dispenser and the main control board for any faults. If necessary, replace the main control board to resolve the issue.

What does an i10 error code mean?

An i10 error code indicates a low water level in the dishwasher. To troubleshoot this issue, check the water supply line for any kinks or blocks that may be restricting water flow. Ensure that the water supply faucet is turned on and providing an adequate water supply to the dishwasher.

How can I address an i20, i40, or iF0 error code?

An i20, i40, or iF0 error code indicates a restricted drain line or clogged filters. Check the drain hose for any blockages or kinks. Clean out the filters and the area around the sump to ensure proper drainage. Additionally, make sure that the knockout plug in the garbage disposal has been removed to allow the dishwasher to drain properly.

What should I do if I see an i30 error code?

An i30 error code indicates water leaking into the base of the dishwasher. To address this issue, check the pressure sensor for any debris and clean it. Then, check the water inlet valve for any blockages or damage that may be causing the leak. Finally, ensure that the drain pump is working correctly and that there are no obstructions blocking the drain pump impeller. Checking that the dishwasher is level can also help prevent water leakage.

What should I do if the issue persists or if I am unsure of how to proceed?

If the issue persists or if you are unsure of how to proceed with troubleshooting the error codes, it is advisable to seek professional assistance. Always refer to the manufacturer’s manual for specific troubleshooting steps and safety precautions.

Source Links