Troubleshooting Guide: Samsung Dishwasher Stops Mid Cycle 4 Easy Steps

If you own a Samsung dishwasher, you may encounter the frustrating problem of it stopping mid-cycle. This issue can disrupt your daily routine and leave you with dirty dishes. But don’t worry, we’re here to help! In this troubleshooting guide, we will provide step-by-step instructions and useful tips to help you resolve the issue and get your dishwasher running smoothly again.

Key Takeaways:

• Stopping mid-cycle is a common problem with Samsung dishwashers.
• Proper troubleshooting steps can help resolve the issue.
• If all else fails, professional assistance may be required.

Common Reasons for Dishwasher Cycle Interruption

It’s frustrating when your dishwasher stops running mid-cycle, leaving you with a sink full of dirty dishes. There are several reasons why your dishwasher might not be finishing its cycle, including:

• A malfunctioning water inlet valve
• A faulty control board
• A clogged drain hose
• An improperly latched door
• Power failure or electrical issues
• Obstructions in the spray arms or filter

If you’re experiencing any of these issues, don’t worry, we’ll help you troubleshoot your Samsung dishwasher and get it back to working properly.

Malfunctioning Water Inlet Valve

The water inlet valve is responsible for letting water into the dishwasher. If it’s not working correctly, your dishwasher may not be able to complete its cycle.

To check if your water inlet valve is malfunctioning:

1. Turn off the power and water supply to your dishwasher.
2. Locate the valve, which is typically located at the bottom of the dishwasher, behind the access panel.
3. Disconnect the wires and hoses from the valve.
4. Use a multimeter to check for continuity. If there is no continuity, the valve needs to be replaced.

If you’re not comfortable checking the water inlet valve on your own, it’s best to contact a professional.

Faulty Control Board

The control board is the brain of your dishwasher, responsible for directing the various functions of the appliance. If it’s not working correctly, it can cause your dishwasher to stop running mid-cycle.

To troubleshoot a faulty control board:

1. Turn off the power to your dishwasher.
2. Access the control board, which is typically located inside the door or behind the panel at the bottom of the dishwasher.
3. Check for any loose wires or damaged components.
4. If everything looks fine, use a multimeter to check for continuity. If the continuity is broken, you’ll need to replace the control board.

Clogged Drain Hose

A clogged drain hose can prevent water from properly draining from your dishwasher, causing it to stop mid-cycle.

To check for a clogged drain hose:

1. Turn off the power and water supply to your dishwasher.
2. Locate the drain hose, which is connected to the sink or garbage disposal.
3. Disconnect the hose and check for any obstructions.
4. If there are any blockages, use a plumber’s snake or a straightened wire hanger to clear the hose.

If you’re unable to clear the clog on your own, consider contacting a professional plumber.

Improperly Latched Door

If the dishwasher door is not properly latched, the appliance will not operate and the cycle will be interrupted.

To check for an improperly latched door:

1. Open the dishwasher door and check for any debris or obstructions around the door latch.
2. Close the dishwasher door and listen for a click, indicating that the latch has engaged.
3. If the latch is not clicking into place, adjust the strike plate or the latch itself until it properly engages.

If you’ve gone through these troubleshooting steps and your dishwasher is still not finishing its cycle, it might be time to contact a professional repair service. Trying to fix the issue on your own could lead to further damage, and it’s always better to be safe than sorry.

Checking the Water Inlet Valve

If your Samsung dishwasher stops mid-cycle, a faulty water inlet valve could be the cause of the problem. Follow these steps to check the valve:

1. Turn off the dishwasher and disconnect it from the power source.
2. Locate the water inlet valve at the bottom of the dishwasher, behind the access panel.
3. Remove the wires from the valve terminals.
4. Place a multimeter on the valve terminals to check the continuity. If the multimeter shows no continuity, the valve is faulty and needs to be replaced.
5. If the valve is working correctly, check the water supply to ensure it’s reaching the valve and not blocked.
6. Reconnect the wires to the valve and put the access panel back on.
7. Turn the power supply back on and run a cycle to see if the issue is resolved.

If this troubleshooting step did not resolve the issue, move on to the next section.

Troubleshooting the Control Board

The control board is the brain behind your Samsung dishwasher’s operation. When it malfunctions, it can cause cycle interruption and other issues. Here are a few troubleshooting steps you can take to identify and resolve control board problems:

1. Turn off the dishwasher: Before you start troubleshooting the control board, make sure the dishwasher is turned off and unplugged from the power source.
2. Inspect the dishwasher wiring: Examine the wiring connections between the control board and other components, such as the motor and sensors. Make sure all connections are tight and secure. If any wiring looks loose or damaged, consider replacing it.
3. Check the control panel: If the control panel is unresponsive or displays error codes, it may indicate a control board issue. Try resetting the control panel by pressing and holding the “Start” button for at least three seconds. If the issue persists, it may be a control board problem.
4. Test the control board: Use a multimeter to test the control board for continuity and other electrical issues. Follow the manufacturer’s instructions for using the multimeter and interpreting the results.
5. Replace the control board: If you’ve identified a control board problem and none of the troubleshooting steps resolve the issue, you may need to replace the control board. Refer to the manufacturer’s instructions or seek professional assistance to ensure proper installation.

Troubleshooting the control board can help identify and resolve cycle interruption issues with your Samsung dishwasher. If you’re unsure about any of the steps or need further assistance, consider reaching out to customer support or hiring a professional dishwasher repair service.

Clearing a Clogged Drain Hose

If your Samsung dishwasher stops mid-cycle, a clogged drain hose could be the culprit. A blocked hose can prevent proper water drainage, leading to an interruption in the cleaning cycle. Here’s how to clear the hose and get your dishwasher back to functioning properly.

Step 1: Turn off the Power

Before attempting to clear the drain hose, turn off the power to your dishwasher to avoid any accidents. This can be done by unplugging the appliance or turning off the circuit breaker.

Step 2: Locate the Drain Hose

The drain hose is usually found at the back of the dishwasher, connected to the drain pump. It’s important to identify the hose before proceeding with the cleaning process.

Step 3: Check for Debris or Blockages

Inspect the drain hose for any debris or blockages that might be causing the obstruction. Use a flashlight to help you see any hard-to-spot particles or food remnants. Remove any visible debris using a pair of pliers or a stiff wire.

Step 4: Detach and Clean the Drain Hose

If the blockage persists, remove the drain hose from the dishwasher and clean it thoroughly. Run water through the tube to flush out any debris or dirt. You can also use a long, flexible brush to remove any stubborn blockages.

Step 5: Reattach the Drain Hose

Once the drain hose is clean, reattach it to the dishwasher. Ensure that it’s securely connected and free from any kinks or bends that might cause future blockages.

Clearing a clogged drain hose can help resolve cycle interruption issues with your Samsung dishwasher. However, if the problem persists, it’s advisable to contact customer support or seek professional repair services for further assistance.

Checking the Door Latch

If your Samsung dishwasher stops mid-cycle, it could be due to an issue with the door latch. An improperly latched door can prevent the dishwasher from running or completing the cycle. Before you call for professional help, follow these simple steps to check the door latch:

1. Open the dishwasher door and inspect the latch mechanism to ensure it’s not damaged or bent.
2. If the latch seems to be in good condition, check the strike plate located on the dishwasher frame. Make sure it’s aligned properly to engage with the latch when the door is closed.
3. If the strike plate is out of alignment, use a screwdriver to adjust it until it fits snugly with the latch mechanism.
4. Close the door and run a cycle to see if the issue is resolved. If the problem persists, move on to the next troubleshooting step.

If you’ve checked the door latch and strike plate but your dishwasher continues to stop mid-cycle or not finish the cycle, the issue may be more complicated.

Don’t worry, there are still options to explore before resorting to a professional repair service. Keep reading to learn more about other troubleshooting steps and when it’s time to call Samsung customer support or a professional repair company.

Resetting the Dishwasher

If your Samsung dishwasher is still experiencing cycle interruption after troubleshooting the common issues, performing a reset might help. This process clears the memory of the dishwasher’s control board and can resolve minor issues. Here’s how to do it:

1. First, turn off the dishwasher and unplug it from the power source.
2. Wait for 5-10 minutes to allow the control board to reset.
3. Plug the dishwasher back in and turn it on.
4. Select the cycle and run the dishwasher to see if the issue has been resolved.

If your dishwasher is still not working correctly, it may require professional assistance. Contact Samsung customer support or consider hiring a professional dishwasher repair service. Sometimes, the issue may be beyond your level of expertise, and it’s best to have a trained technician assess and repair it.

“Resetting your dishwasher can sometimes resolve minor issues causing cycle interruption.”

Don’t let dishwasher problems disrupt your daily routine. By following the troubleshooting guide and performing a reset, you can solve most issues that cause cycle interruption. If all else fails, don’t hesitate to contact customer support or professional repair services for help.

Cleaning the Filter and Spray Arms

One of the most common reasons for your Samsung dishwasher to stop mid-cycle is a dirty filter or clogged spray arms. Over time, the filter and spray arms can become clogged with food debris, soap scum, and hard water deposits. This can impact the dishwasher’s performance and cause it to stop functioning correctly. Fortunately, cleaning the filter and spray arms is a simple process that you can easily perform at home. Here’s how:

Cleaning the Filter

The filter is designed to trap food particles and prevent them from clogging the dishwasher’s drainage system. To clean the filter, follow these steps:

1. Remove the bottom dish rack from the dishwasher.
2. Locate the filter at the bottom of the dishwasher and twist it counterclockwise to remove it.
3. Rinse the filter under warm water to remove any food particles or debris.
4. Use a soft-bristled brush to scrub away any remaining residue from the filter.
5. Rinse the filter with water once again, and then reattach it to the dishwasher by twisting it clockwise.

Regularly cleaning the filter will ensure that your Samsung dishwasher runs smoothly and prevents mid-cycle interruptions.

Cleaning the Spray Arms

The spray arms distribute water throughout the dishwasher to clean your dishes. Over time, the spray arms can become clogged with food particles, soap scum, and hard water deposits, which can impact their performance. To clean the spray arms, follow these steps:

1. Remove the top dish rack from the dishwasher.
2. Locate the spray arms and twist them counterclockwise to remove them from the dishwasher.
3. Inspect the spray arms for any clogs or blockages and remove any debris with a toothbrush or small brush.
4. Rinse the spray arms with warm water to remove any remaining debris.
5. Reattach the spray arms to the dishwasher by twisting them clockwise.

Regularly cleaning the spray arms will ensure that your Samsung dishwasher runs efficiently and prevents mid-cycle interruptions.

Contacting Samsung Customer Support

If you have exhausted all troubleshooting steps and your Samsung dishwasher continues to stop mid-cycle, it may be time to reach out to Samsung customer support for further assistance.

You can contact Samsung through their website or by phone. Before reaching out, make sure to have your dishwasher’s model and serial number on hand, as well as a detailed description of the issue you are experiencing. This will help the customer support team better assist you.

“I contacted Samsung customer support when my dishwasher continued to stop mid-cycle despite trying all the troubleshooting steps. The representative was friendly and knowledgeable, and after asking a few questions, recommended a local repair service. I appreciated their prompt and helpful assistance.”

– John D.

Don’t hesitate to contact Samsung customer support if you’re experiencing issues with your dishwasher. They are there to help you get back to enjoying a fully-functional appliance in no time.

Hiring Professional Repair Services

If the troubleshooting steps have not resolved the issue and your dishwasher is still not finishing the cycle, it might be time to contact a professional repair service. Hiring a professional company ensures that the issue is correctly diagnosed and fixed, saving you time and money in the long run. Additionally, attempting to make repairs on your own could cause further damage or even pose a risk to your safety.

When choosing a dishwasher repair service, it is essential to pick a reputable company with experienced technicians. Look for companies that specialize in dishwasher repairs and have good reviews online. You can also ask for recommendations from friends or family who have had dishwasher repairs in the past.

Do not hesitate to contact a professional repair service if the troubleshooting steps have not resolved the issue. It is better to have your dishwasher fixed by an experienced technician than risk doing more harm than good.

Conclusion

Troubleshooting a Samsung dishwasher that stops mid-cycle can be a frustrating experience, but it doesn’t have to be. By following the steps outlined in this guide, you can identify and resolve common dishwasher issues that lead to cycle interruption.

Remember to check the water inlet valve, control board, drain hose, door latch, and clean the filter and spray arms regularly. If the issue persists, reach out to Samsung customer support or a professional repair service to get your dishwasher back to functioning smoothly.

Don’t let a malfunctioning dishwasher ruin your day. Take action today to address the common issues that cause cycle interruption and enjoy a hassle-free dishwasher experience.