While GE Profile refrigerators are top-performing high-end units, it doesn’t negate that their ice makers are not trouble-free. More and more customers complain of GE Profile refrigerator ice maker problems French door.
Some of these problems affecting GE profile French door units include an ice maker that won’t make ice, a noisy or slow one, an ice maker that won’t turn on, and an option that won’t stop. We also have those that don’t work after rest.
Interestingly, despite the setbacks, most of these ice maker problems are DIY fixable, proving that GE refrigerators are good. To prove that, I’ll share a troubleshooting guide for these six issues, highlighting their probable causes and applicable DIY fixes.
Once you master these DIY fixes, you won’t be among those users who can’t stop complaining about the refrigerator’s ice maker.
Let’s get started.
In a hurry? Below is a quick troubleshooter for the common GE Profile French door ice maker problems.
GE Profile Refrigerator Ice Maker Problems French Door Troubleshooting Guide
Problem | Possible Cause | Fix | |
1. | Ice Maker Won’t Make Ice | The ice maker or water supply is off, wrong freezer temperature, a blocked water filter or valve, faulty door switch, or inadequate water pressure | Turn the ice maker and water supply on, lower the freezer temperature, replace the clogged water filter or valve, raise the water pressure, and replace the faulty door switch, depending on the cause |
2. | Noisy Ice Maker | Insufficient water, water supply is off, the fridge is too close to the wall, or pump blockage | Turn on the water supply, move the refrigerator away from the wall, or unclog the drain pump, depending on the cause |
3. | Slow Ice Maker | Low water pressure, high freezer temperature, frozen line, or the obstructed water filter | Raise the water pressure, lower the freezer temperature, defrost the water line or replace the clogged filter, depending on the cause |
4. | Ice Maker Runs Endlessly | Sensor failure | Inspect the sensor and replace it if faulty |
5. | Ice Maker Won’t Turn On | Ice maker not turned on, ‘Child Lock’ or just faulty | Turn the ice maker on, replace it if it’s defective, and deactivate ‘Child Lock.’ |
6. | Ice Maker Doesn’t Work After Reset | Low water pressure, ‘Child Lock,’ water line blockage, or wrong reset procedure | Increase the water pressure, deactivate the ‘Child Lock’ function, unblock the water line, or follow the correct reset procedure – depending on the cause of the problem |
Explaining The 6 Common GE Profile Refrigerator Ice Maker Problems French Door
Discussed below are 6 of the most everyday DIY fixable GE Profile French door ice maker problems you should be wary of:
1. GE Profile Ice Maker Won’t Make Any Ice
Nothing annoys like a high-end ice maker that won’t make ice. GE Profile refrigerator ice makers belong in the high-end category. So, they disappoint when their ice maker fails.
In general, GE Profile refrigerator ice makers won’t work due to any of these reasons:
- Ice maker might be off – Your GE Profile ice maker won’t make any ice if it’s off. You’ve to check it to ensure it’s turned on. If it is, then consider the other possibilities shared below.
- Water supply might be off – The ice maker is not the only thing you need to turn on before making some ice. You also need to turn on the water supply as the ice maker needs water to make ice.
- High freezer temperature – The right freezer temperature is 0 – 50F. Anything outside this range, more so above 100F, causes the ice maker to stop working.
- Blocked water filter valve – For the water to reach the ice maker, it must go through the water filter and valve. If any of the two is clogged, water won’t pass through, and your GE ice maker won’t have any for the ice production.
- Low water pressure – Your GE ice maker requires a water pressure of at least 20 psi to make ice. You can measure it using a home water pressure gauge. If it’s lower than 20 psi, adjust the pressure from the main valve and remove any kinks or blockages on the water line.
- Faulty door switch – A faulty door switch won’t allow your GE refrigerator to run, so your ice maker won’t work. You can check if the door switch is defective by testing it for continuity using a multimeter.
2. Noisy GE Profile Ice Maker
You expect the ice maker to make some noise while operating the compressor. It should, however, not be too loud.
You also expect the ice maker to make some noise when heating (during water freezing). However, if the noise is deafeningly loud, knocking-like, you should watch out for any of these causes:
- Insufficient water pressure – Your GE refrigerator will make a loud humming noise if the low pressure is low to show that it’s not receiving enough water. For that reason, checking the water pressure using a pressure gauge is advisable to ensure it’s at least 20 PSI.
- Water supply is off – Your GE Profile ice maker will also make noise if the main water supply valve is off. All it takes to correct that is to turn the water supply on.
- The fridge is resting too close to the wall – If your GE unit is closer to the wall, there’s always the chance it will vibrate and rub against the wall. If that happens, the fridge will vibrate loud. So, consider moving it away from the wall.
- Possible pump blockage – A blocked pump won’t pump water, which means none will get to the ice maker for the ice production. So, check your pump for clogging and clean it properly.
3. Slow GE Profile Ice Maker
Sometimes your French door GE ice maker may produce some ice but in a slower manner. If that’s the case, then the ice maker problem could be because of any of the following:
- Low water pressure – Your GE Profile ice maker will run slowly if the water pressure is insufficient. The pressure should be at least 20psi for the GE ice maker to work at its optimum best.
- Higher freezer temperature – Your GE Profile refrigerator ice maker requires a freezer temperature of about 0 – 50F to work best. If the temperature is above 50F, it makes it hard for the ice maker to make ice. So, adjust it accordingly,
- Frosted water line – Ice frosting in the water line makes it hard for the ice maker to receive water; if it doesn’t, it won’t make any ice. Thus, check the water line for possible frosting and use a hairdryer to defrost it.
- Obstructed water filter – If the water filter is excessively clogged, likely after several months, no water will reach the ice maker for ice production. Therefore, replacing the GE refrigerator water filterat least once every six months is advisable.
4. GE Profile Refrigerator French Door Ice Maker Runs Endless (Won’t Stop Running)
Your GE Profile ice maker may run without stopping until something goes wrong, which is just as concerning as an ice maker that won’t make any ice.
The only possible explanation for that is a faulty sensor. So, you need to inspect the ice maker sensor for faults and possibly use a multimeter to test it. If it’s faulty, replace it.
5. GE Profile French Door Refrigerator Ice Maker Won’t Turn On
How about an ice maker that won’t turn on? If that happens, the reason could be any of these three reasons:
- Ice maker might be off – You cannot expect your GE Profile ice maker to turn on until you switch it on. So, check its switch to ensure it’s turned on.
- ‘‘Child Lock’’ might be on – ‘Child Lock’ deactivated most GE Profile fridge functions, including the ice maker. So, ensure you deactivate it first.
- Ice maker might be faulty – If the ice maker is on and the ‘Child Lock’ off, but it won’t turn on, the chances are that it’s defective.
Overall, it’s advisable not to try and repair an ice maker. Instead, you should get a replacement. You’ll, however, need to take out the old to fit its replacement.
How to Remove Ice Maker from GE Profile French Door Refrigerator
Follow these steps to do it:
- Unplug your GE Profile refrigerator from the power
- Open the unit’s door on the left side and take out the ice bucket
- Unscrew the cover that’s above the ice maker
- Disconnect the wires connecting to the ice maker and unthread the screw holding the ice maker
- Then lift the old ice maker
- You can then take the ice maker to a fridge expert to examine it or use it to find a replacement
6. GE Profile Refrigerator Ice Maker Doesn’t Work After Reset
You expect your GE Profile French door ice maker to start making ice immediately after resetting it. This is, however, not a given as the ice maker sometimes fails to do so, and you wonder why.
Here are the possible explanations:
- Low water pressure – You should check the water pressure after resetting your GE Profile ice maker to ensure it is enough to pump water to the ice maker. Work with at least 20 psi.
- ‘Child Lock’ – Check the ‘‘Child Lock’’ function to ensure it’s off. If not, deactivate it as a ‘Child Lock’ and deactivate most fridge functions, including the ice maker.
- Water line blockage – There is also the possibility of your GE ice maker failing after a reset if there’s a blocked water line. Check the water line for obstruction and clear it, lest the ice maker won’t work.
- Wrong reset procedure – You must reset your GE profile refrigerator ice maker correctly. If not, your ice maker won’t work, and the entire GE Profile French door refrigerator ice maker reset will be a disappointment.
Closing Thought on GE Profile Refrigerator Ice Maker Problems French Door!
Above are the commonest GE Profile French door ice maker problems you need to get familiar with. As shared, you can troubleshoot these problems independently, saving you money as you don’t have to pay a fridge technician.
But if the problem is too technical or you are just not handy, don’t hesitate to talk to an expert.
Also Read: