Every GE refrigerator fan would want to own a GE profile unit. Reason? The units are the perfect embodiment of class, functionality, and efficiency. Sadly, their ice makers are not the most reassuring, especially when you are green regarding GE Profile refrigerator ice maker troubleshooting.
Common GE Profile refrigerator ice maker issues to troubleshoot on your own include an ice maker that doesn’t produce any ice or one that makes them slow or discolored. We also have a noisy ice maker and an option that won’t work after replacing its filter.
Overall, several possible explanations exist for each problem, and I’m here to help you break them down. We’ll discuss the five issues, their probable causes, and relevant fixes.
After that, we’ll talk about how you can reset your GE profile ice maker to try and bypass some of the solutions, especially when you aren’t sure about the cause of the problem.
Let’s get started:

In a rush? Refer to the table below if you want to troubleshoot your GE Profile refrigerator but do not have the time to read the entire article.
Quick GE Profile Refrigerator Ice Maker Troubleshooting Guide
Problem | Possible Cause | Fix | |
1. | No Ice Production | Turned off ice maker or water supply, low water pressure, clogged filter or valve, or faulty door switch or ice tray | Turn both the ice maker and water on, adjust the water pressure, or replace the clogged filter valve, door switch, or ice tray, depending on the exact cause |
2. | Slow Ice Production | Clogged water filter or water line, reduced water pressure, Warmer or dirty freezer, reduced food load, or leaky door seal | Unclog the water filter and water line, increase the water pressure, reduce the freezer temperature, keep the freezer clean, increase the food load, or replace the door seal, depending on the exact problem |
3. | Discolored Ice | Plumbing issues or contaminated household water | Fix the plumbing issue and report any household water contamination |
4. | Noisy Ice Maker | Disconnected water supply | Check the water supply and connect it before turning the ice maker on |
5. | Failed Ice Maker After Filter Replacement | Air vent blockage, dead motor, or old filter | Don’t overload the freezer; replace the motor, and use a new filter, depending on the cause |
5 Common Problems with GE Profile Refrigerator Ice Maker for Troubleshooting
Discussed below are common issues GE profile refrigerator ice makers suffer, which you can troubleshoot:
1. No Ice Production
This is probably the most typical problem among GE refrigerator ice maker users around the globe. It’s the reason most users question whether GE refrigerators are good.
Most don’t know that the cause is often something simple that doesn’t call for expert intervention.
Here are some suggestions:
a) Turn The Ice Maker On
It’s worth checking the ice maker as it could be off. You’ve to turn it on if you want it to do its job.
b) Turn The Water Supply First Before the Ice Maker
While turning the ice maker on is essential, that shouldn’t come before connecting the water supply. Remember, your GE ice maker needs water to produce ice.
Thus, connect the water supply first before turning the ice maker on.
c) Adjust The Water Pressure to 20psi at Least
Measure your home water pressure using a water pressure gauge. If the pressure is lower than 20psi, unkink or unblock the pipe if it has kinks or ice blockage.
It may also help if you adjust the water pressure from the primary regulator and clean the valve.

d) Replace The Water Filter, Water Valve, Or Both If Clogged
It’s worth checking the condition of the water filter and valve as they directly impact the ice maker’s ice production.
The water filter, for example, should be replaced after six months. Failure to do so will translate to a clogged filter that won’t allow any water to get to the ice maker, which means your GE ice maker won’t have the raw material (water) for making ice.
As for the water inlet valve, it also clogs over time, requiring a replacement. The problem with a clogged water inlet valve is that it reduces the water pressure and flow to the ice maker, thus preventing ice production.
e) Test The Door Switch for Continuity
Let’s now talk about your GE Profile refrigerator door switch. If the door switch is faulty, the ice maker won’t work.
So, it’s worth testing it for continuity using a digital multimeter to determine if it’s defective. If the switch does not register any continuity on the device, it’s faulty.
Consequently, you’ll need to replace it. You can also take the opportunity to test the ice maker on/off switch for continuity, just in case, there’s nothing wrong with the door switch.
If your GE Profile refrigerator ice maker on/off switch shows no continuity, it’s likely to be defective. Thus, replace it.
f) Check The Ice Tray for Cracking
Lastly, you should inspect your ice tray for possible cracking if your GE ice maker won’t make any ice. If the ice tray has cracks, it won’t be able to rotate. If it doesn’t, it won’t empty the ice.
So, replace the ice tray if you notice a cracked one.
2. Your GE Ice Maker Not Making Ice Fast Enough
Sometimes, your GE profile refrigerator ice maker may make some ice slowly. That can be as frustrating as an ice maker that won’t make any ice.
Overall, here are some suggestions if you have a slow-running ice maker:
a) Inspect The Water Filter For Clogging
While a wholly clogged water filter prevents water from reaching the ice maker, a partially clogged one slows the ice-making process.
In this case, consider the possibility of the latter. Like in the first case, you should replace a clogged filter, especially one you’ve used for over six months.

b) Inspect The Water Line for Ice Clogging
Your GE Profile refrigerator water line could be ice-frozen. So, inspect it for possible ice clogging and unfreeze it. It may mean using a hairdryer to defrost the water line or unplugging the unit to allow the water line to self-defrost.
c) Check The Water Pressure
If only a tiny amount of water is getting to the ice maker, the water pressure will always be lower than it should be.
So, again, measure the water pressure with a water pressure gauge and adjust it to at least 20 psi using the tips shared earlier.
d) Reduce Your Freezer Temperature
The GE refrigerator freezer works best within the temperature range of 0 – 5 0F. If you misadjust the temperature to over 100F, the freezer will be too warm, delaying the ice-making process.
e) Clean Your GE Freezer as It Could Be Dirty
Too much dirt clogs the air vents, interfering with air circulation. If there’s no adequate air circulation, the freezer will overwork, slowing ice production.
f) Improve Your Food Load
Loading a small amount of food into your GE freezer or refrigerator only slows ice production. Your GE unit needs enough food load to stabilize its working temperature and allow the ice maker to work at an ideal condition. The freezer compartments should be more than ½ full.
g) Inspect Your Fridge Door Seal for Air Leakage
Your ice maker will only work optimally when the freezer is cold. That, however, may not be the case if the fridge door seal is old, as it’ll allow air to escape.
The problem with air leakage is that it makes the freezer warmer and slows down the ice maker.
3. GE Profile Refrigerator Ice Maker Making Discolored Ice
Another common problem facing GE Profile ice makers is discolored (or dirty ice) production. If that’s the case, it could be because of the following:
a) Your Plumbing Could Be Faulty
Check for the possibility of having a plumbing defect. A pipe could be allowing dirt into your home water supply. You’ll need to find it and fix it.
b) Your Water Supply Could Be Contaminated
Sometimes your home water supply could be contaminated from the source or somewhere outside your home, affecting the water’s appearance. If so, you should report to your local water supplier/authority.

4. Noisy GE Profile Refrigerator Ice Maker
One of the most familiar GE Profile refrigerator ice maker problems French door is noise. Sometimes, the ice maker makes a buzzing, rattling, or vibrating sound while struggling to fill up the water. That’s likely to happen if the water supply is off or disconnected.
Fix
Ensure you connect the water supply and turn the water on before the ice maker. That should stop the weird noise.
5. Ice Maker Failing to Work After Filter Replacement
You expect your GE Profile ice maker to start working after replacing the filter. That, however, may not be the case because of any of these reasons:
a) Blocked Air Vents
Food can block the air vents around the freezer, interfering with its performance and that of the ice maker. So, you’ll need to space food in the freezer to avoid blocking the air vents.
b) Faulty Motor
Check the motor to ensure it’s working well. If it’s dead, replace it.
c) Old Filter
If you replace your filter and return a used one, there’s a chance it won’t work. So, avoid reusing water filters and use a new one when doing the replacement.

GE Profile Refrigerator Ice Maker Reset
Here are the general steps for resetting your GE Profile refrigerator ice maker:
- Unplug your GE Profile refrigerator from the power
- Wait for 60 seconds to plug the fridge back into the electrical outlet
- Try switching the ice maker on to see if it’s working
- If your ice maker doesn’t work after the above steps, hold the GE Profile refrigerator ice maker test switch for about 10 seconds
- Your ice maker should reset after that
- If it doesn’t, consider checking your unit’s manual to see if there’s something you can do differently.
Closing Thought On GE Profile Refrigerator Ice Maker Troubleshooting!
Now you have a detailed troubleshooting guide for common GE Profile refrigerator problems.
Depending on the problem that relates to your unit, you can use the guide to try and fix it. Remember, you can always go back to your manual or call an expert if the fix doesn’t work.
Also Read: