Maytag Centennial washers are top performers; there’s no doubt about that. But like all top-performing washers, these washers suffer a few issues, especially during their spin cycle. The good news is that most Maytag Centennial washer spin cycle problems are fixable.
Common fixable Maytag Centennial spin cycle problems include a washer that won’t spin at all, one that doesn’t spin well, a low spinning option, and one that spins violently. Others neither spin nor drain, while some are just noisy when spinning.
So, there are at least six problems the washer may experience during the spin cycle. The silver lining is that you don’t need a technician to help you fix them once you know what to look at.
This guide will supplement your washer manual to help you troubleshoot these spin cycle-related problems. We’ll highlight the possible causes for each spin cycle problem and its DIY fix.
Let’s get into it:
In a rush? Check out a quick troubleshooter of these spin cycle problems below:
Troubleshooting Guide for Common Maytag Centennial Washer Spin Cycle Problems
| Spin Cycle Problem | Problem Cause | DIY Fix | |
| 1. | Washer Won’t Spin At All | Load imbalance, open lid, or wrong cycle | Balance the load, close the lid and select the correct wash setting |
| 2. | Washer Doesn’t Spin Well/Correctly | Loose drive belt or defective suspension rods, or shift actuator | Tighten the drive belt if loose and replace the suspension rods or shift actuator if defective |
| 3. | Washer Spins Slowly | Unbalanced load or washer | Balance the laundry and put the washer on level ground |
| 4. | Washer Spins Violently | Broken shock dampeners, excess load, unbalanced laundry, or unstable washer | Replace broken shock dampeners, reduce the excess load and balance it, and adjust the washer’s level leg |
| 5. | Washer Neither Spins Or Drain | Clogged drain, faulty drain pump, excess load, or excess suds | Unclog the drain, replace the defective drain pump, reduce laundry load and avoid excess detergent |
| 6. | Noisy Spin Cycle | Bad bearing or worn out splash wheel or wash plate | Replace the washer bearing, splash wheel, or wash plate if faulty |
Common Maytag Centennial Washer Spin Cycle Problems and Solutions
Discussed are seven common spin cycle problems prevalent on Maytag centennial washers and their solutions:
1. Maytag Centennial Washer Won’t Spin at All
Here are the primary reasons why most Maytag Centennial washers won’t spin at all:
a) Load Imbalance
Your Centennial washers won’t spin if your laundry is not well balanced. You need the clothes to be evenly spread for the washer to spin.
Fix – Rearrange and rebalance your laundry if they look unproportioned. Always do that before every spin cycle.
b) Open Lid
The Maytag Centennial will only work if you close its seal. An open lid means you are not ready to run the washing machine.
Fix – Ensure you close the washer’s lid before you start the wash cycle.
c) Wrong Cycle Setting
You have to select the correct cycle for the washer to spin. Overall, your choice depends on the laundry you are washing. For example, choose delicate or gentle settings for fragile fabrics and slow spin for bulky clothes.
Fix – Ensure you match the wash cycle with your laundry.
Other Reasons Why Your Maytag Centennial Washer Gets Stuck On Spin Cycle
While the above three causes are the most typical explanations for a Maytag Centennial that won’t spin, other less common causes include:
a) Damaged Motor Coupling
A damaged motor coupling will prevent the washer from spinning. Often, that happens when you wash heavy loads.
Fix – Replace the damaged motor coupling.
b) Stuck Item
A stuck item in the washer drum can sometimes prevent it from spinning. It could be a piece of clothes, debris, or a small loose metal object like a broken zipper or coin.
Fix – Stop your washer and open the drain to inspect it. Then look for any stuck item and remove it.
c) Clogged Drain Loose
A clogged drain hose interferes with the water drainage, preventing the washer from spinning.
Fix – Inspect the detain hose for clogging. Just look into the hose near a source of light. If you can’t see through, your drain hose is blocked. So, you should unclog it.
You can use a pressure washer drain cleaner to do it.
d) Faulty Drive Belt
Your Maytag Centennial won’t spin if the drive belt is loose or damaged. Remember, the belt moves the pulley system, which, in turn, rotates the washer. So, if the drive belt is faulty, the pulley system won’t move, and the washer won’t spin.
Fix – Tighten the drive belt onto the pulley system if loose. Replace it, however, if it’s damaged.
e) Worn Out the Clutch Transmission or Bearing
Also, observe the clutch, transmission, and bearing for wearing. If any component is old, your Maytag Centennial washer won’t spin.
2. Maytag Centennial Washer Doesn’t Spin Well
Sometimes, your Maytag Centennial may spin but not perfectly. It could be stopping mid-cycle or spinning irregularly. If that’s the case, the cause could be any of the following:
a) Loose Drive Belt
If the drive belt is loose, the washer may not spin at all (as in the first case) or spin correctly. You need the drive belt to attach to the pulley tightly to move the pulley properly, and the pulley will, in turn, rotate the washer.
Fix – Tighten the drive belt onto the pulley system if loose.
b) Faulty Shift Actuator
Your Maytag Centennial won’t spin or agitate if the shift actuator is faulty.
Fix – Run a diagnostic on your Maytag Centennial to confirm that the shift actuator is really faulty. If it is, then replace it.
c) Defective Suspension Rods
Bad suspension rods won’t absorb the impact force, making it hard for the washer to spin.
Fix – Get a replacement for the suspension rods if they are faulty.
3. Maytag Centennial Washer Has a Slow Spin Cycle
Some issues interfere with the Maytag Centennials spinning speed, slowing the washer down. These issues include the following:
a) Unbalanced Load
The washer won’t spin at regular speed if the clothes are not evenly balanced. Instead, the washer will spin at a slower pace.
Fix – Rearrange your load if it’s unbalanced before you start washing.
b) Washer Imbalance
The washer may also spin very slowly if it’s not leveled correctly. An unstable washer causes the laundry to fall out of place, thus making it unbalanced.
Fix – Position the washing machine on a more stable surface. You can also try to readjust its legs to ensure it’s not unstable.
4. Maytag Centennial Washer Shaking Violently On Spin Cycle
Nothing could be more alarming than a Maytag Centennial washer that violently shakes when spinning. That is often the case due to any of these reasons:
a) Broken Shock Dampeners
If the shock dampeners (suspension rods or shock absorbers) are damaged, they won’t absorb the energy released by the spinning washer. And as a result, the washer will violently shake when spinning.
Fix – Replace the suspension rods or shock absorbers if they are broken and faulty.
b) Excess Load
Excessively loading the washer may cause it to shake when spinning. That’s more likely to happen when you choose a fast spin cycle.
Fix – Reduce your laundry load to about ¾ full before re-spinning the washer.
c) Load Imbalance
It’s not just an overload that can make your Maytag Centennial spin violently but also an imbalance load.
Fix – Redistribute your laundry in the washer tub to avoid a load imbalance.
d) Unstable Washer
Also, consider the possibility of your washer’s legs not being correctly leveled. If that’s the case, the washer will shake violently, often because of a load imbalance.
Fix – Adjust your washer legs to ensure the washer stands on level ground and doesn’t violently shake when spinning.
5. Maytag Centennial Washer Neither Spins nor Drains
At times, your Maytag Centennial may fail not just to spin but also to drain. If that’s the case, the reason could be any of the following:
a) Clogged Drain
A clogged drain makes it hard for your washer to spin or drain, ultimately paralyzing its operation.
Fix – Clean your clogged drain, preferably with a drain cleaning hose to unblock it.
b) Faulty Drain Pump
A faulty pump makes it hard for the water to drain. And if the waste water doesn’t drain, the washer won’t spin.
Fix – Replace the drain pump if it’s faulty.
c) Excess Load
A laundry overload will interfere with the washer’s spin cycle and drainage.
Fix – Don’t overload your washers more than ¾ full. If that’s the case, reduce the load.
d) Excess Suds
If excess suds form from too much detergent, your washer will fail to spin and drain.
Fix – Avoid using too much detergent, especially when washing with soft water.
6. Maytag Centennial Washer Has a Noisy Spin Cycle
Lastly, another common Maytag Centennial washer problem is noise during the spin cycle. Your Maytag Centennial washer may make weird noise during spinning because of any of these two reasons:
a) Bad Bearings
if your Maytag Centennial makes a jet engine sound, the problem is the faulty bearing.
Fix – Replace the washer bearing if it’s defective.
b) Worn-Out Splash Wheel/Wash Plate
If your washer makes a high-pitched whirring noise, the problem is often a worn-out splash wheel, wash plate, or both.
Fix – Replace the splash wheel or wash plate, depending on what is faulty.
People Also ask
1. Why Will My Maytag Centennial Washer Not Spin?
Your Maytag Centennial washer won’t spin because of an open lid, load imbalance, wrong spin cycle, damaged motor coupling, or faulty drive belt.
Other possible causes include a worn-out clutch, transmission, or bearing.
2. How Do You Reset a Maytag Washer’s Spin Cycle?
You can reset the spin cycle on a Maytag washer by pressing its start/pause key for about 3 seconds while the washer is on standby. Then, you need to rotate the central knob anti-clockwise to clear the previous sequence and reset the washer.
Closing Remarks!
Above are the six most familiar Maytag Centennial washer spin cycle problems that are easier to fix even though most users are unaware of. You can, thus, refer to the troubleshooting guide whenever your Maytag Centennial develops an issue during its spin cycle.