6 Reasons Your Maytag Centennial Washer Not Spinning!

It frustrates when the Maytag Centennial won’t spin. It means you cannot do your laundry until you fix it. So, is your Maytag centennial washer not spinning, and you are not sure why? 

Your Maytag Centennial washer won’t spin due to jammed or uneven clothes, imbalance, wrong setting, clogged drain or obstructed drum. It could also fail to spin due to a failed component such as the lid switch, motor coupling, drive belt, clutch, transmission, or shift actuator.

Most of these reasons are also why your Centennial washer won’t just spin but won’t also drain. Others may allow the clothes to spin, but it won’t spin, dry your clothes or stop spinning mid-cycle.   

I’ll also share the three issues to enable you to know what exactly to check when your Maytag Centennial suffers any spin cycle problem.

I’ll help you put your washer on diagnostic mode to find any hidden error code and probably reset it. 

Let’s jump into it!

In a rush? Find below a DIY troubleshooting guide for your non-spinning Maytag Centennial washer:

Quick Troubleshooting Guide for A Maytag Centennial Washer Not Spinning

What Causes a Maytag Centennial Washer Not to Spin?

Below are six reasons why a Maytag Centennial washer won’t spin:

1. Jammed or Uneven Clothes

If you overload the clothes in your Centennial washer, the laundry machine may fail to spin. The load will become too bulky to turn within the drum, and even if it turns, you’ll likely have wet clothes at the end of the spin. (Clonazepam)  

That explains why Maytag recommends a ¾ loading. That leaves enough room for the clothes to spin.

Note that while you may not have overloaded the clothes, they may fail to turn if they are not uniform in the washer. So, this is another thing to watch out for when loading your Centennial washer. 

Fix 

Reduce the clothes load if they are jammed/overloaded. Remember to keep the load ¾ full. So, you may have to take out some of the clothes. Meanwhile, spread them evenly in the washer to ensure they can spin smoothly.

2. Machine Imbalance 

Your Centennial washer could also fail to spin because it’s out of balance. That could be because its feet are loose or it’s resting on an uneven surface. So, you’ve to figure out which of the two is stopping your washer from turning, especially when it vibrates when you turn it on. 

Note that often, the reason why you have uneven laundry is that of an imbalance washer. So, you could fix two issues here.

Fix 

Adjust the washer’s feet if they are loose and ensure they are uniform. Then ensure the washer is resting on stable/uniform ground. 

If it’s not, move it. But before you can run the washer, check the clothes to ensure they are even. If not, redistribute them uniformly. 

3. Wrong Setting for Bulky Clothes

An incorrect setting could explain why your washer won’t spin bulky clothes. For example, if you’ve selected a Low-Spin cycle, the washer will spin at an almost unnoticeable pace. And if the No-Spin cycle is on, the washer won’t spin at all.

Also, if you use a Delicate, Hand Washing, or Gentle setting on bulk clothes, the clothes won’t spin. So, you must choose the right setting for your washer, depending on the clothes you wash. 

Fix 

Confirm that you are using the right setting. If a No-Spin or Low-Spin cycle is on, consider opting for a high-speed setting for your bulky load. Only use such settings on less bulky clothes and when you need more soaking than spinning. 

4. Clogged Drain 

Your Centennial washer may not spin because of poor drainage. If the drain hoses are clogged, water will stagnate in the washer tube. 

That means that even if the washer spins, which is less likely, you’ll have wet clothes at the end of the cycle. So, inspect the drain hose to ensure the water drains smoothly. 

Fix 

Detach the drain pipe to inspect it for clogging. If the drain pipe is dirt clogged, run hot water to unclog it. 

5. Obstructed Drum

The washer might not be spinning because of something in the drum obstructing it. Start by looking for debris in the drum, which could deter the washer from turning. 

If there’s no debris, then the obstruction could be trapped clothes. It could also be a combination of the two. 

Fix 

Inspect the washer’s drum for debris and clothes obstructions and remove them before running the washer.

6. Component failure

Lastly, if the reason why your Centennial washer won’t spin is none of the above 6, then it could be a failed component. One of these components could be worn out, damaged, or dysfunctional, thus preventing the washer from spinning. 

• Lid switch – The lid switch enables the lid to close. If the lid won’t close, the dryer may not run and will likely not spin. You can know if the lid switch is faulty if it lacks continuity. 
• Motor coupling – The motor coupling, which links the transmission system and motor, may prevent the washer from spinning if it fails. So, inspect it for damage and wear. 
• Drive belt – If the drive belt is loose or broken, the washer won’t spin properly or may fail to do so at all. So, you should examine it and consider replacing it if it appears faulty. 
• Clutch – The clutch connects the transmission system and the inner washer tub, thus essential in spinning. If it’s worn out, the washer won’t spin. 
• Transmission – The transmission system is another essential component that enables the Centennial washer to spin. However, it wears out over time. Once that happens, the washer won’t spin. 
• Shift actuator – The washing machine will also not spin if the shift actuator is faulty.

Fix 

Carefully examine all the above components for fault and replace the worn-out or malfunctioning ones. Talk to a laundry machine expert if you cannot do the component replacement DIY.

Other Maytag Centennial Spinning Issues

Maytag Centennial Washer Stopped Spinning Mid-Cycle

Issues like power failure, an error code, or a wrong cycle selection could stop the centennial washer from spinning mid-cycle. Regarding an incorrect cycle selection, the washer will stop spinning if you select a low-spin or no-spin cycle mid-cycle.

And when it comes to power failure, the washer will stop spinning mid-cycle due to a tripped breaker or exploded fuse. You also have to watch out for a power outage.

And if there is an error code, clear it first by resetting the washer (steps shared below). 

Maytag Centennial Washer Not Spinning Clothes Dry

If your Maytag Centennial washer won’t spin clothes dry, it’s likely because of a wrong setting, especially a no-spin or low spin. It could also be that the load is excess and out of balance. If so, you need to reduce the load size and balance it. 

It may help to select a high-spin to remove the excess water properly.

The washer could also fail to spin dry clothes because it’s unstable or due to a clogged drain. Also, consider the possibility of a power failure, a faulty lid switch, or excessive suds. 

Maytag Centennial Washer Not Spinning or Draining

Your Maytag Centennial is neither spinning nor draining because of an excess load, a clogged drain, or excessive suds. So, check the laundry load to ensure the clothes are not jamming.

Then check the drain pipe for clogging and unblock it and avoid using too much detergent if there are excessive suds.

Also, consider the possibility of a bad lid switch preventing the lid from closing. Other possible explanations include a worn-out clutch or transmission, which won’t allow the washer to spin.

How to Put a Maytag Centennial Washer in Diagnostic Mode?

Suppose you cannot find why your Centennial washer won’t spin. If so, putting your Centennial washer in diagnostic mode is advisable. 

That will allow you to discover hidden error codes that could point you to the reset problem. Here’s how to do it:

• Put your washer on standby mode (power it off, but don’t unplug it)
• Position the control knob on the noon position
• Rotate the knob three times clockwise, once anti-clockwise, and one more time clockwise

How to Reset a Maytag Centennial Washer?

You can fix some issues and clear error codes by resetting your washer. Here’s how to reset a Centennial washing machine:

• Unplug the laundry machine for 20 seconds
• Plug it back and restart the washer
• If the washer still doesn’t reset, unplug it for at least 10 minutes

People Also Ask

What Do You Do When a Maytag Washing Machine Won’t Spin?

Consider checking the laundry load, settings, and washer leveling when your Maytag washer won’t spin. If the laundry is overloaded, reduce it to ¾ full; if it’s uneven, spread it evenly.

In the meantime, ensure you are using the right setting and that the laundry is not out of balance. 

How Can I Reset a Maytag Washer Not Spinning?

You can reset your non-spinning washer by unplugging it for about 20 seconds. If the washer doesn’t restart, unplug it for 10 minutes or even up to 30 minutes. 

Meanwhile, try to determine if something prevents the washer from spinning. 

Is the issue resolved after replacing the hub?

After installing the new hub and taking the extra step of recalibrating the washing machine, I am grateful for Jake’s assistance. I have high hopes that this new hub will result in a longer-lasting resolution to the issue.

Is the new hub an OEM part?

“I went to A1 Appliance Store in Montgomery, AL yesterday and purchased another hub for my washer. Before opening the package, I wanted to confirm whether it is an OEM part or an aftermarket one. I will contact the store today to inquire about its origin. The salesperson at the store suggested that the issue might be caused by overloading the washer, but I have been cautious about not exceeding its capacity since I first replaced the hub. However, I want to ensure that the new hub is indeed an OEM part. Upon further inspection, I compared the part number you provided with the one printed on the package, and they are identical. Based on this, it can be concluded that the new hub is an OEM part.”

Has the washer been recalibrated after replacing the hub?

Yes, the washer has been recalibrated after replacing the hub.

Has the hub been checked again after replacing it?

“Yes, I have indeed checked the hub again after replacing it. Not only did I successfully install the new hub, but I also took the extra step of recalibrating the washing machine, something I neglected to do during my first attempt. I appreciate your assistance, Jake. With these measures in place, I am hopeful that this time the washing machine will have a longer lifespan.”

Where was the hub purchased from and is it an aftermarket or OEM part?

The hub was purchased from A1 Appliance Store in Montgomery, AL. The customer, however, is uncertain whether it is an aftermarket or OEM part and plans to inquire with the store. They mentioned that the store suggested that the issue could have been caused by overloading the washer, but the customer denies doing so since the first replacement. The customer discovered that the part number provided by the assistant matches the one on the package, leading them to believe that it is an OEM part.

What parts have been replaced in the washer?

Several parts have been replaced in the washer. Initially, the worn out plastic clutch in the agitator was replaced, which resolved the previous issue. However, a new problem has now emerged. Upon examining the belt clutch that connects to the tub, everything appeared to be intact and properly secured. No loose components were observed, and the belt was evenly positioned from one end to the other.

Closing Remarks 

Now you know how to fix a Maytag centennial washer not spinning. You should consider several issues when your washer won’t spin at all, stop spinning mid-cycle, or fail to spin dry. 

That includes jammed or uneven laundry, imbalance washer, wrong setting, drain clogging, drum obstruction, or component malfunction.

And as shared, the components to pay attention to include the lid switch, motor coupling, drive belt, clutch, shift actuator, and transmission.